Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT (for Automatic Air Conditioning System)

AIR CONDITIONING UNIT (for Automatic Air Conditioning System) > INSTALLATION

for Preparation Click here



1. INSTALL AIR CONDITIONING UNIT ASSEMBLY


    E173246
  1. Install the air conditioning unit with the bolt and nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



2. INSTALL INSTRUMENT PANEL REINFORCEMENT


  1. Install the instrument panel reinforcement with the 6 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    E173245



  1. Install the 3 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



    E173244

  1. Connect the connectors.



  1. Attach the 13 clamps.


    E173243



    E173242
  1. Install the grommet to the vehicle body.



    I045581E01
  1. Connect the ground wires to the instrument panel reinforcement with the 2 bolts.



    E173240
  1. Connect the 2 connectors.

  1. Attach the clamp.



    E173238
  1. Connect the connector and wire harness.

  1. Attach the clamp.

  1. Install the drain hose.



3. INSTALL ECM
  1. for 1GR-FE:
    Install the ECM (Click here).

  1. for 1KD-FTV:
    Install the ECM (Click here).

  1. for 2KD-FTV:
    Install the ECM (Click here).

  1. for 2TR-FE:
    Install the ECM (Click here).



4. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


E173236
  1. Install the instrument panel junction block with the 2 nuts.

  1. Connect the connectors.

  1. Install the brace with the nut and 2 bolts.



5. INSTALL NO. 4 AIR DUCT


E173235
  1. Attach the 2 claws to install the air duct.



6. INSTALL NO. 2 AIR DUCT


E173234
  1. Attach the 2 claws to install the air duct.



7. INSTALL NO. 1 AIR DUCT


E173233
  1. Attach the 2 claws to install the air duct.



8. INSTALL NO. 3 HEATER TO REGISTER DUCT


E173232
  1. Attach the 4 claws to install the duct.

  1. Install the clip.



9. INSTALL NO. 1 HEATER TO REGISTER DUCT


E173231
  1. Attach the 3 claws to install the duct.

  1. Install the clip.



10. INSTALL NO. 2 HEATER TO REGISTER DUCT


E173230
  1. Install the duct with the clip.



11. INSTALL STEERING COLUMN ASSEMBLY
  1. Install the steering column assembly (Click here).



12. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Install the lower instrument panel (Click here).



13. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Install the upper instrument panel (Click here).



14. CONNECT HEATER WATER HOSE OUTLET A
  1. Connect the water outlet hose and attach the clip.



15. CONNECT HEATER WATER HOSE INLET A
  1. Connect the water inlet hose and attach the clip.



16. CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
  1. Remove the vinyl tape attached to the air conditioning tube and accessory.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the air conditioning tube and accessory.

  1. Connect the air conditioning tube and accessory.



17. CONNECT SUCTION TUBE SUB-ASSEMBLY


    I043225E01
  1. Remove the vinyl tape attached to the tube.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction tube.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the suction tube.

  1. Connect the suction tube and attach the piping clamp.

    HINT:
    After the connection, check that the claw of the piping clamp is engaged.

  1. Install the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



19. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).



20. ADD ENGINE COOLANT
  1. for 1GR-FE:
    Add engine coolant .

  1. for 1KD-FTV (w/ EGR Cooler):
    Add engine coolant .

  1. for 1KD-FTV (w/o EGR Cooler):
    Add engine coolant .

  1. for 2KD-FTV (w/ EGR Cooler):
    Add engine coolant .

  1. for 2KD-FTV (w/o EGR Cooler):
    Add engine coolant .

  1. for 2TR-FE:
    Add engine coolant .



21. CHARGE REFRIGERANT
SST
09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)
  1. Perform vacuum purging using a vacuum pump.



  1. Charge refrigerant HFC-134a (R134a).

    Standard:
    450 +- 30 g (15.87 +- 1.05 oz.)



    I037365E02

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
    1. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, and not with the sight glass.



22. WARM UP ENGINE
  1. Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging refrigerant.

    NOTICE:
    After removing and installing the cooler refrigerant lines (with the compressor), be sure to warm up the compressor when turning the A/C switch ON. This is done to prevent damage to the compressor.



23. CHECK FOR ENGINE COOLANT LEAKS
  1. for 1GR-FE:
    Check for engine coolant leaks .

  1. for 1KD-FTV (w/ EGR Cooler):
    Check for engine coolant leaks .

  1. for 1KD-FTV (w/o EGR Cooler):
    Check for engine coolant leaks .

  1. for 2KD-FTV (w/ EGR Cooler):
    Check for engine coolant leaks .

  1. for 2KD-FTV (w/o EGR Cooler):
    Check for engine coolant leaks .

  1. for 2TR-FE:
    Check for engine coolant leaks .



24. CHECK FOR LEAKAGE OF REFRIGERANT
  1. After recharging the refrigerant gas, prepare the vehicle for a refrigerant gas leakage check by making sure the following conditions are met.

    1. The ignition switch is OFF.
    2. The vehicle is in a place with good air ventilation and without any volatile gases, such as evaporated gasoline or exhaust gas. The detector is very sensitive to volatile gases. If volatile gases are unavoidable, the vehicle must be lifted up.
    3. Some refrigerant is remaining in the refrigerant system.
    4. The compressor is OFF and its pressure is approximately 392 to 588 kPa (4 to 6 kgf/cm2).



    I042222E03
  1. Check for refrigerant gas leakage from the refrigerant line.

    1. After the blower motor stops, wait at least 15 minutes.

    2. Using a gas leak detector, check that gas is not leaking from the refrigerant line. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Check for refrigerant gas leakage from the cooling unit.

    1. Hold the gas leak detector so that the sensor is under the drain hose, as shown in the illustration.

    2. Check that gas is not leaking from the drain hose. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Check for refrigerant gas leakage from the cooling unit.

    1. Remove the blower motor control from the unit. Insert the gas leak detector's sensor into the unit.

    2. Check that gas is not leaking from the unit. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Check for refrigerant gas leakage from the pressure switch.

    1. Disconnect the pressure switch connector and wait approximately 20 minutes.

    2. Using a gas leak detector, check that gas is not leaking from the pressure switch. If leakage is found, tighten parts or replace damaged parts as necessary to stop the leak.

  1. Repeat all steps above 2 to 3 times.