Home › BODY › INTERIOR › FUEL LID LOCK CONTROL

FUEL LID LOCK CONTROL > INSTALLATION

for Preparation Click here



1. INSTALL FUEL FILLER OPENING LID LOCK RETAINER


B084759E01
  1. Install the lock retainer and turn it counterclockwise as shown in the illustration.



2. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY


B084760E01
  1. Install the cable and turn the lock retainer clockwise as shown in the illustration.

  1. Attach the cable to the clamps shown in the illustration.

  1. Install the grommet to the vehicle body.



  1. Install the open lever.


    B085267E02



    B113218E02



    B113219E02



3. INSTALL REAR WHEEL HOUSE LINER LH
  1. Install the rear wheel house liner.



4. INSTALL REAR NO. 1 WHEEL OPENING EXTENSION LH (w/ Over Fender)
  1. Attach the 11 clips to install the extension.



  1. Install the 7 screws.


    B086893E01



5. INSTALL FLOOR CARPET ASSEMBLY FRONT (for RHD)
  1. Install the floor carpet.



6. INSTALL QUARTER INSIDE TRIM BOARD LH (for Extra Cab)


    B085707E01
  1. Attach the claws and install the trim pocket to the trim board.

  1. Attach the 7 clips and 6 claws to install the trim board.



    B113105
  1. Connect the front seat outer belt's anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B114992
  1. Connect the rear No. 1 seat belt's anchor with the built-in bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



7. INSTALL QUARTER TRIM PANEL LOWER LH
  1. for Single Cab:
    Install the back panel trim .

  1. for Double Cab:
    Install the back panel trim .



8. INSTALL CENTER PILLAR GARNISH LOWER LH (for Double Cab)


    B085563E01
  1. Attach the 2 clips and 2 claws to install the garnish.



    B085693E02
  1. Connect the front seat outer belt's anchor with built-in bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



9. INSTALL BACK PANEL TRIM (w/ Back Panel Trim)
  1. for Single Cab:
    Install the back panel trim .

  1. for Double Cab:
    Install the back panel trim .



10. INSTALL REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH (for RHD, for Extra Cab)


B113856E02
  1. Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt A

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt B



    B087825
  1. Install the bolt and close the cover as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B089599E02
  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B114992E01
  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



11. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH


B084917E01

NOTICE:
Do not disassemble the retractor.

  1. w/o Pretensioner single cab and extra cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B084922E01
  1. w/o Pretensioner Double cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf }



    B113098E03
  1. w/ Pretensioner:
    Install the bolt and seat belt.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt A

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B



    B114993
  1. w/ Pretensioner:
    Connect the pretensioner connector as shown in the illustration.



    B084915E01
  1. Single cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Close the cover.



    B084920E01
  1. Extra cab and double cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the cap.



    B085691E01
  1. Single cab:
    Install the quarter trim panel lower. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085692E01
  1. Extra cab:
    Install the quarter inside trim board. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085693E01
  1. Double cab:
    Install the anchor of the seat belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



12. INSTALL REAR DOOR SCUFF PLATE LH (for Double Cab)


B085564E01
  1. Attach the 2 clips and 7 claws to install the scuff plate.



13. INSTALL COWL SIDE TRIM BOARD LH (for LHD)


B085566E01
  1. Attach the 2 clips to install the trim board.

  1. Install the cap nut.



14. INSTALL COWL SIDE TRIM BOARD RH (for RHD)

HINT:
Use the same procedures described for the LH side.



15. INSTALL FRONT DOOR SCUFF PLATE LH
  1. for Single Cab:
    Install the front door scuff plate .

  1. for Extra Cab:
    Install the front door scuff plate .

  1. for Double Cab:
    Install the front door scuff plate .



16. INSTALL FRONT DOOR SCUFF PLATE RH (for RHD)
  1. for Single Cab:
    Install the front door scuff plate .

  1. for Extra Cab:
    Install the front door scuff plate .

  1. for Double Cab:
    Install the front door scuff plate .



17. INSTALL CONSOLE BOX SUB-ASSEMBLY


B090153E01
  1. Install the console box with the 2 clips, 4 screws <F> and 2 bolts <E>.



18. INSTALL CONSOLE PANEL SUB-ASSEMBLY UPPER


B115418E02

NOTICE:
Be careful not to damage the instrument panel lower and console box with the claws of the console panel upper.

  1. Attach the 12 claws to install the console panel.



19. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY


B087844E02
  1. Attach the 4 claws to install the hole cover.



20. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


B111105E01
  1. w/ M/T:
    Twist the knob in the direction indicated by the arrow to install it.

  1. w/ 4WD:
    Twist the transfer shift lever knob in the direction indicated by the arrow to install it.



21. INSTALL REAR SEATBACK ASSEMBLY (for Extra Cab)


    B108088E01
  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Attach the seatback's 2 hooks to the vehicle body.

  1. Install the seat with the 2 bolts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 in.*lbf }



22. INSTALL BACK PANEL GARNISH LOWER (for Extra Cab)


B085704E01
  1. Attach the 5 clips and 6 claws to install the garnish.



23. INSTALL BACK PANEL GARNISH UPPER
  1. for Single Cab:
    Install the back panel garnish upper .

  1. for Extra Cab:
    Install the back panel garnish upper .

  1. for Double Cab:
    Install the back panel garnish upper .



24. INSTALL REAR SEAT CUSHION ASSEMBLY LH (for Extra Cab)


    B115404E02
  1. Attach the seat cushion's 2 rear hooks to the vehicle body.



    B115402E01
  1. Attach the seat cushion's front hook to the rear seat cushion lock hook. Then install the seat cushion.

  1. Confirm that the seat cushion is firmly installed.



25. INSTALL REAR SEAT CUSHION ASSEMBLY RH (for Extra Cab)

HINT:
Use the same procedures described for the LH side.



26. INSTALL REAR SEAT ASSEMBLY (for Double Cab)
  1. Install the rear seat assembly (Click here).



27. INSTALL FRONT SEAT ASSEMBLY LH

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.

  1. w/ Front Seat Side Airbag:
    Install the front seat assembly (Click here).

  1. for Separate Seat Type:
    Install the front seat assembly (Click here).



28. INSTALL FRONT SEAT ASSEMBLY RH

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.

  1. w/ Front Seat Side Airbag:

    HINT:
    Use the same procedure described for the LH side.

  1. for Separate Seat Type:

    HINT:
    Use the same procedure described for the LH side.

  1. for Bench Seat Type:
    Install the front seat assembly (Click here).

  1. for RHD, for Power Seat:
    Install the front seat assembly (Click here).



29. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).