Home › ENGINE ยท 1KD-FTV › LUBRICATION › OIL PUMP (w/ EGR Cooler)

OIL PUMP (w/ EGR Cooler) > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A099591E01
  1. Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.



  1. Loosen the cylinder block drain cock plug.


    A147246E01



3. REMOVE ENGINE ASSEMBLY
  1. Remove the engine (Click here).



4. REMOVE FUEL INLET PIPE SUB-ASSEMBLY


    A152281
  1. Remove the bolt and clamp.



    A153562
  1. Remove the bolt and oil level gauge guide.



    A152282E02
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.



5. REMOVE EGR COOLER WITH ELECTRIC EGR CONTROL VALVE AND NO. 2 EGR VALVE
  1. Remove the EGR cooler (Click here).



6. REMOVE NO. 4 INJECTION PIPE


    A152275
  1. Remove the bolt and disconnect the injection pipe clamp.



    A152276E02
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.



7. REMOVE VENTILATION PIPE


    A151169
  1. Remove the bolt and ventilation pipe.



8. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A152277
  1. Remove the 3 bolts and disconnect the 4 connectors.



    A060180E01
  1. Using a small screwdriver, remove the holder seal by prying the portion between the holder seal and the cutout part of the cylinder head.

  1. Disconnect the ventilation hose.



    G034877E01
  1. Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.



9. REMOVE TIMING BELT
  1. Remove the timing belt (Click here).



10. REMOVE CAMSHAFT TIMING PULLEY


    A060182E01
  1. Remove the bolt of the camshaft timing pulley by holding the camshaft with a wrench.

    NOTICE:
    Make sure to remove the bolt of the camshaft timing pulley with the timing belt not installed.

  1. Remove the camshaft timing pulley.



11. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY


12. REMOVE CYLINDER BLOCK INSULATOR


    A149941
  1. Remove the cylinder block insulator from the cylinder head.



13. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts, nuts and No. 2 timing belt cover.



14. REMOVE WATER PUMP ASSEMBLY


    A225339
  1. Remove the 2 nuts, 5 bolts, water pump and gasket.



15. REMOVE TIMING GEAR COVER INSULATOR


    A148171
  1. Remove the bolt and timing gear cover insulator.



16. REMOVE VACUUM PUMP ASSEMBLY


A098930E01
  1. Disconnect the vacuum hose.

  1. Remove the 2 nuts, vacuum pump and O-ring.



17. REMOVE VANE PUMP ASSEMBLY
  1. Remove the 2 nuts, vane pump and O-ring.

    HINT:
    It is not necessary to remove the hose from the vane pump. For the remaining removal procedures, you may put the removed assembly aside in an appropriate location.



18. REMOVE PUMP DRIVE SHAFT PULLEY


A038747E01
  1. Remove the 4 bolts, No. 2 camshaft timing pulley flange and pump drive shaft pulley.



    A070711E03
  1. Using SST, hold the crankshaft pulley and remove the nut and O-ring.

    SST
    09213-58013  
    09330-00021  



19. REMOVE CRANKSHAFT PULLEY


    A072413E02
  1. Using SST, remove the pulley bolt.

    SST
    09213-58014  
    09330-00021  



    A072414E02
  1. Using SST, remove the pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.



20. REMOVE CRANKSHAFT POSITION SENSOR
  1. Disconnect the sensor connector.



  1. Remove the 3 clips, bolt and sensor.


    A112048



21. REMOVE CAMSHAFT POSITION SENSOR


A112046
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.



22. REMOVE TIMING GEAR COVER


A038748E01
  1. Remove the wire harness clamp.

  1. Remove the 14 bolts and 2 nuts.

  1. Using a slotted screwdriver, gently separate the cover from the timing gear case.

    HINT:
    There are tiny slots that allow you to insert the slotted screwdriver tip for separating the timing gear case and its cover. Refer to the illustration for the slot locations.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing gear case and its cover.

  1. Remove the cover and O-ring.



23. FIX NO. 1 IDLE GEAR


A038749E01
  1. Fix the sub idle gears to the idle gear with the service bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    If the screw hole position of the rear sub idle gear is incorrect, rotate the crankshaft counterclockwise to correct the hole position. Then install the service bolt.

    HINT:
    The service bolt is installed to eliminate torsional force caused by the idle gear springs, which are located between the idle gear and each sub idle gear. Torsional force will cause the sub idle gear's tooth and idle gear's tooth to be out of alignment.



24. REMOVE CRANKSHAFT TIMING GEAR


    A060163E01
  1. Remove the No. 1 crankshaft position sensor plate.



    A071161E01
  1. Using SST, remove the crankshaft timing gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05010)



25. REMOVE NO. 1 IDLE GEAR


A038751E01
  1. Remove the 2 bolts, idle gear thrust plate.

  1. Remove the service bolt and idle gear.

  1. Remove the No. 1 idle gear shaft.



26. REMOVE INJECTION GEAR


A071164E01
  1. Using SST, remove the injection gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



27. REMOVE FUEL SUPPLY PUMP ASSEMBLY


    A153558
  1. Disconnect the 2 fuel hoses.



    A153559
  1. Disconnect the 2 connectors.



    A070710E01
  1. Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.



    A070711E02
  1. Remove the set nut and O-ring while holding the crankshaft pulley by using SST.

    SST
    09213-58013  
    09330-00021  



    A153560
  1. Loosen the 2 nuts.



    A070714E01
  1. Using SST, disconnect the pump from the injection gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and pump.

    NOTICE:
    1. Do not hold the pump or carry it holding the pipe.
    2. The pump must be kept horizontal.

  1. Remove the O-ring.



28. REMOVE OIL DIPSTICK GUIDE


A148132
  1. Remove the bolt and injection pipe clamp.

  1. Remove the bolt and guide.

  1. Remove the O-ring from the guide.



29. REMOVE OIL PAN SUB-ASSEMBLY
  1. Remove the 22 bolts and 2 nuts.



    Z004119E04
  1. Insert the blade of a oil pan seal cutter between the cylinder block and oil pan. Cut through the applied sealer and remove the oil pan.

    NOTICE:
    1. Do not use a oil pan seal cutter for the timing gear case and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.

  1. Remove the 2 bolts, nut, oil strainer and gasket.

  1. Clean off any sealer remaining the oil pan and cylinder block.



30. REMOVE TIMING GEAR CASE ASSEMBLY


A038755E01
  1. Remove the 8 bolts and union bolt. Then remove the timing gear case and its 2 O-rings.

    NOTICE:
    Do not drop the oil pump rotor.

  1. Remove the nut and No. 1 vacuum transmitting pipe.

  1. Remove the oil pump gasket.