ENGINE ASSEMBLY > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE HOOD SUB-ASSEMBLY |
Disconnect the washer nozzle hose.
Remove the 4 bolts and hood.
| 3. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD and Pre-Runner) |
Remove the 4 bolts and No. 1 engine under cover.
| 4. REMOVE NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner) |
Remove the 2 bolts and No. 2 engine under cover.
| 5. DRAIN ENGINE OIL |
Remove the oil filter cap.
Remove the oil drain plug, and drain the engine oil from the oil pan.
| 6. LOOSEN FUEL TANK CAP ASSEMBLY |
| 7. DRAIN ENGINE COOLANT |
![]() |
Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.
Loosen the cylinder block drain cock plug and the radiator drain cock plug.

| 8. REMOVE BATTERY BRACKET |
| 9. REMOVE BATTERY AND BATTERY TRAY |
| 10. REMOVE AIR CLEANER ASSEMBLY |
for Ventilation Hose Type:
Disconnect the ventilation hose.
Disconnect the mass air flow meter connector.
Loosen the hose clamp.
Remove the 2 bolts and air cleaner.
| 11. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ EGR Cooler) |
![]() |
Remove the 3 bolts, 2 nuts and engine cover.
| 12. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/o EGR Cooler) |
![]() |
Remove the 3 bolts, 2 nuts and engine cover.
| 13. REMOVE INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR (w/ EGR Cooler) |
![]() |
Detach the 2 clamps.
Disconnect the vacuum hose from the manifold absolute pressure sensor.
Disconnect the IAT sensor connector and manifold absolute diesel pressure sensor connector.
![]() |
Loosen the 2 clamps.
![]() |
Remove the 4 bolts and intercooler.
| 14. REMOVE INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR (w/o EGR Cooler) |
![]() |
Disconnect the IAT sensor connector and manifold absolute diesel pressure sensor connector.
Disconnect the vacuum hose from the manifold absolute pressure sensor.
![]() |
Loosen the 2 clips.
![]() |
Remove the 4 bolts and CAC.
| 15. REMOVE RADIATOR ASSEMBLY |
| 16. DISCONNECT HEATER HOSE |
![]() |
Disconnect the 2 heater hoses.
| 17. DISCONNECT PRESSURE FEED TUBE ASSEMBLY |
![]() |
Disconnect the oil reservoir to pump hose.
![]() |
Disconnect the pressure feed tube.
| 18. DISCONNECT FUEL HOSE |
![]() |
Disconnect the 2 fuel hoses.
| 19. DISCONNECT UNION TO CONNECTOR TUBE HOSE |
![]() |
Disconnect the union to connector tube hose.
| 20. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Push in the sides of the glove compartment door, as indicated by the arrows in the illustration. Then open the door to release it from the 2 stoppers. Open the door until it is horizontal.
![]() |
Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
| 21. DISCONNECT WIRE HARNESS |
![]() |
Remove the upper relay block cover.
Remove the side relay block cover.
Remove the nut and disconnect the engine room junction block wire.
Disconnect the 2 engine room junction block connectors.
Remove the bolt and disconnect the ground cable.
![]() |
Remove the 2 nuts, detach the clamp and disconnect the wire harness.
![]() |
Disconnect the 3 EDU connectors.
Disconnect the 4 ECM connectors.
![]() |
Disconnect the turbo motor driver connector.
w/ A.D.D.
Disconnect the 4WD control ECU connector.
for Automatic Transmission:
Disconnect the 3 TCM connectors.
Disconnect the 4 ECU connectors.
| 22. DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System) |
Remove the 4 bolts and disconnect the cooler compressor.
| 23. REMOVE TRANSMISSION ASSEMBLY |
| 24. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission) |
![]() |
Place matchmarks on the clutch cover and flywheel.
Loosen each set bolt one turn at a time until spring tension is released.
Remove the 6 set bolts and pull off the clutch cover.
| 25. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission) |
| 26. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission) |
![]() |
Using SST, hold the crankshaft pulley.
![]() |
Remove the 8 bolts and flywheel.
| 27. REMOVE PUMP IMPELLER DRIVE PLATE (for Automatic Transmission) |
![]() |
Using SST, hold the crankshaft pulley.
![]() |
Remove the 8 bolts, the rear drive plate spacer, the pump impeller drive plate, and the flywheel and ring gear.
| 28. REMOVE REAR END PLATE |
Remove the bolt and end plate.
| 29. REMOVE ENGINE ASSEMBLY |
![]() |
Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.
| No. 1 Engine hanger | w/ EGR Cooler | 12284-30060 |
| Bolt (91552-81014) | ||
| w/o EGR Cooler | 12284-30020 | |
| Bolt (91552-81014) | ||
| No. 2 Engine hanger | 12282-67030 | |
| Bolt (91642-81030) | ||
Attach an engine sling device and hang the engine with a chain block.
![]() |
Remove the bolt and No. 2 cylinder block insulator.
![]() |
Remove the 4 bolts and 4 nuts.
Remove the engine by operating the engine sling device and chain block.
| 30. FIX ENGINE ON ENGINE STAND |
| 31. REMOVE ENGINE WIRE |
Remove the engine wire.
| 32. REMOVE NO. 1 TIMING BELT COVER |
![]() |
Remove the bolt and water hose clamp.
Remove the wire harness clamp.
Remove the 6 bolts and timing belt cover.
| 33. REMOVE TIMING BELT |
| 34. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, remove the pulley bolt.
![]() |
Using SST, remove the pulley.
| 35. REMOVE TURBOCHARGER SUB-ASSEMBLY (w/ EGR Cooler) |
| 36. REMOVE TURBOCHARGER SUB-ASSEMBLY (w/o EGR Cooler) |
| 37. REMOVE EXHAUST MANIFOLD |
![]() |
Remove the 8 nuts and exhaust manifold.
| 38. INSPECT EXHAUST MANIFOLD |
![]() |
Using a precision straightedge and feeler gauge, measure the surface contacting the cylinder head for warpage.
| 39. REMOVE GENERATOR ASSEMBLY |
![]() |
Remove the nut and generator wire.
Disconnect the generator connector.
Remove the 2 bolts and generator.
| 40. REMOVE GENERATOR BRACKET |
Remove the bolt and generator bracket.
| 41. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the 4 bolts and V-ribbed belt tensioner.
| 42. REMOVE INTERCOOLER SUPPORT BRACKET |
Remove the 2 bolts and intercooler support bracket.
| 43. REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET |
Remove the 2 bolts and No. 2 intercooler support bracket.
| 44. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System) |
Remove the 4 bolts and No. 1 compressor mounting bracket.
| 45. REMOVE WATER INLET |
![]() |
Remove the 3 bolts and water inlet.
| 46. REMOVE THERMOSTAT |
| 47. REMOVE WATER OUTLET |
![]() |
Remove the 2 bolts and water outlet.
| 48. REMOVE GLOW PLUG ASSEMBLY |
| 49. REMOVE OIL FILTER SUB-ASSEMBLY |
![]() |
Using SST, remove the oil filter.
| 50. REMOVE INTAKE MANIFOLD |
| 51. INSPECT INTAKE MANIFOLD |
![]() |
Using a precision straightedge and feeler gauge, measure the surface contacting the cylinder head for warpage.
| 52. REMOVE FUEL SUPPLY PUMP ASSEMBLY |
![]() |
Remove the bolt and clamp.
Remove the 2 bolts and oil level gauge guide.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
![]() |
Disconnect the 2 fuel hoses.
![]() |
Disconnect the 2 connectors.
![]() |
Remove the 4 bolts indicated by the arrows in the illustration.
Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.
![]() |
Remove the set nut and O-ring while holding the crankshaft pulley by using SST.
![]() |
Loosen the 2 nuts.
![]() |
Using SST, disconnect the pump from the injection gear.
Remove the 2 nuts and pump.
Remove the O-ring.
| 53. REMOVE COMMON RAIL ASSEMBLY |
Disconnect the 2 connectors.
![]() |
Remove the 2 bolts, common rail and No. 2 intake manifold insulator.
| 54. REMOVE OIL COOLER COVER SUB-ASSEMBLY |
![]() |
Disconnect the oil pressure switch connector and wire harness.
Remove the 2 nuts and No. 2 vacuum transmitting pipe.
Remove the 13 bolts and oil cooler cover.
| 55. REMOVE TIMING GEAR COVER INSULATOR (w/ EGR Cooler) |
![]() |
Remove the bolt and timing gear cover insulator.
| 56. REMOVE VACUUM PUMP ASSEMBLY |
![]() |
Remove the 2 nuts, vacuum pump and 2 O-rings.
| 57. REMOVE VANE PUMP ASSEMBLY |
![]() |
Remove the 2 nuts, vane pump and O-ring.
| 58. REMOVE CRANKSHAFT POSITION SENSOR |
Remove the bolt and crankshaft position sensor.
| 59. REMOVE CAMSHAFT POSITION SENSOR |
Remove the bolt and camshaft position sensor.
| 60. REMOVE ENGINE COOLANT TEMPERATURE SENSOR |
Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor and gasket.
| 61. REMOVE FRONT ENGINE MOUNTING INSULATOR |
Remove the 2 nuts and 2 front engine mounting insulators.
| 62. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET RH |
![]() |
Remove the 4 bolts and No. 1 front engine mounting bracket.
| 63. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH |
Remove the 4 bolts and No. 1 front engine mounting bracket.