DTC C1268/68 Transfer "L4" Position Switch Circuit |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1268/68 | No signal is input to the EXI4 terminal of the skid control ECU. |
|


| 1.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI4 TERMINAL) |
![]() |
Turn the ignition switch off.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S35-9 (EXI4) - Body ground |
| 11 to 14 V |
| S35-9 (EXI4) - Body ground |
| Below 1.5 V |
|
| ||||
| OK | |
| 2.RECONFIRM DTC |
Clear the DTC(s) (Click here).
Turn the ignition switch off.
Check if the same DTC is recorded.
| Result | Proceed to |
| DTC is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI4 TERMINAL) |

Turn the ignition switch off.
Disconnect the skid control ECU connector.
for A/T:
Disconnect the transmission control ECU connector.
Disconnect the L4 position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S35-9 (EXI4) - T4-1 | Always | Below 1 Ω |
| S35-9 (EXI4) - Body ground | Always | 10 kΩ or higher |
| T4-2 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.INSPECT L4 POSITION SWITCH (TRANSFER INDICATOR SWITCH NO. 1) |
![]() |
Remove the L4 position switch (transfer indicator switch No. 1) (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Pushed | Below 1 Ω |
| 1 - 2 | Free | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (L4 POSITION SWITCH POWER SOURCE CIRCUIT) |
![]() |
Turn the ignition switch off.
Disconnect the L4 position switch connector.
Disconnect the skid control ECU connector.
for A/T:
Connect the transmission control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Ignition switch ON | 11 to 14 V |
| Result | Proceed to |
| OK | A |
| NG (for M/T) | B |
| NG (for A/T) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TRANSMISSION CONTROL ECU) |

Turn the ignition switch off.
Disconnect the skid control ECU connector.
Disconnect the transmission control ECU connector.
Disconnect the L4 position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S35-9 (EXI4) - T18-15 (L4) | Always | Below 1 Ω |
| S35-9 (EXI4) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||