ECD SYSTEM (w/ EGR Cooler) > Lack of Power or Hesitation |
| Malfunction Condition | Main Trouble Area | Related Trouble Area |
| (a) Injector malfunctions
|
|
| Faults and Symptoms of Common Rail Diesel Components |
Engine Control
| Main fault | Decrease in performance (foreign matter is stuck) |
| Symptoms | Lack of power, black smoke |
| Data List | MAF |
| |
| Symptom: Main fault |
|
| Data List |
|
| Main fault |
|
| Symptoms | Lack of power (when vehicle starting, when heavy load) (Black smoke is not emitted when racing while vehicle stopped) |
| Data List | MAP (inside intake air pressure), Target Booster Pressure
|
| Main fault | Blockage |
| Symptoms | Lack of power (high engine speed, when heavy load) |
| Data List | MAP (inside intake air pressure), Target Booster Pressure When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt. |
| Main fault | Open circuit, glow plug relay fault |
| Symptoms | Difficult to start, rough idle, knocking, white smoke (when cold) |
| Data List | Check the glow plug indicator light |
| Diagnostic Point | Try to measure the resistance of the glow plug |
| Main fault | Damaged, seized up |
| Symptoms | Cannot crank, crank speed is low, strange noise |
| Main fault | Loss of compression |
| Data List | Engine Speed of Cyl#
|
Diesel Injection
| Main fault | - |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power |
| Data List | Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
|
| Diagnostic Trouble Code | Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored. |
| Main fault | Blockage |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power |
| Data List | Fuel Press, Target Common Rail Pressure
|
| Diagnostic Trouble Code | Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored. |
| Main fault | Blockage |
| Symptoms | Rough idle, lack of power, black smoke, white smoke, knocking |
| Data List | Injection Feedback Val
|
| Main fault | Circuit fault: The fuel injector does not open. |
| Symptoms | Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking |
| Data List | Same as fuel injector |
| Diagnostic Trouble Code | When the EDU has a fault, some DTCs may be stored. |
| Main fault | Open circuit, decrease in performance (foreign matter is stuck) |
| Symptoms | Difficult to start, rough idle, engine stall, lack of power |
| Data List | Fuel Press, Target Common Rail Pressure
|
| Diagnostic Code | When the fuel pressure sensor has a fault, some DTCs may be stored. |
| Main fault | - |
| Symptoms | Difficult to start, rough idle (especially when cold) |
Diesel EGR
| Main fault |
|
| Symptoms |
|
| Data List | Actual EGR Valve Pos., Target EGR Position
|
Diesel Throttle
| Main fault | Stuck, does not move smoothly |
| Symptoms |
|
| Data List |
|
| Data List Related to Lack of Power |
| Explanation of Symptom |
| Lack of Power | The power of the diesel engine is determined by the quantity of injected fuel and the quantity of intake air. The quantity of injected fuel is determined by the fuel pressure and the amount of time the injector is open for. Basically, the fuel pressure is controlled to reach the target fuel pressure. The throttle valve does not restrict air flow volume, so the manifold absolute pressure is almost the same as atmospheric pressure when idling. At more than approximately 1500 rpm, the turbo starts to operate causing the manifold absolute pressure to become higher than atmospheric pressure. The manifold absolute pressure is controlled to reach the Target Booster Pressure when accelerating the vehicle at full throttle. Also, when accelerating the vehicle at full throttle, the throttle is fully open and the EGR valve is fully closed, preserving the mass air flow. |
| 1.READ OUTPUT DTC (RELATING TO ENGINE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
| Result | Proceed to |
| No DTCs are output | A |
| Engine related DTCs are output | B |
|
| ||||
| A | |
| 2.TAKE SNAPSHOT DURING IDLING AND 4000 rpm |
![]() |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
With no load after the engine is warmed up, take a snapshot when idling and at 4000 rpm.
| NEXT | |
| 3.TAKE SNAPSHOT DURING LACK OF POWER |
![]() |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
Take a snapshot of the following Data List items with the intelligent tester during lack of power.
Check for a lack of power during the driving test.
| Result | Proceed to |
| Apparent lack of power is present | A |
| Apparent lack of power is not present | B |
|
| ||||
| A | |
| 4.CHECK SNAPSHOT (MAP AND MAF) |
Check MAP and MAF in the snapshot taken when the engine was running at 4000 rpm with no load.
| Result | Proceed to |
| MAP is 117 kPa or more and MAF is 84 g/sec. or more*1 | A |
| MAP is less than 90 kPa*2 | B |
| Except above*3 | C |
|
| ||||
|
| ||||
| A | |
| 5.CHECK SNAPSHOT (FUEL PRESS, TARGET COMMON RAIL PRESSURE, MAP AND TARGET BOOSTER PRESSURE) |
Check Fuel Press, Target Common Rail Pressure, MAP and Target Booster Pressure in the snapshot taken when the vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.
| Result | Proceed to |
| MAP is less than 205 kPa at an engine speed of 3000 rpm | A |
| Difference between Fuel Press and Target Common Rail Pressure is +/-20000 kPa or more | B |
| Except above | C |
|
| ||||
|
| ||||
| A | |
| 6.CHECK INTAKE SYSTEM |
Check for air leakage and blockage between the air cleaner and turbocharger, and between the turbocharger and intake manifold.
|
| ||||
| OK | |
| 7.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER |
Clean the fuel filter case and replace the fuel filter.
| NEXT | |
| 8.REPLACE FUEL INJECTORS OF ALL CYLINDERS |
Replace the fuel injectors (Click here).
| NEXT | |
| 9.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 10.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING |
Register the injector compensation code .
Perform the fuel injector pilot quantity learning .
| NEXT | |
| 11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 12.READ VALUE USING INTELLIGENT TESTER (MAP AND ATMOSPHERIC PRESSURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.
Compare MAP to Atmosphere Pressure when the ignition switch is ON (do not start the engine).
| Result | Proceed to |
| MAP and Atmosphere Pressure have the same value | A |
| MAP is different from actual atmospheric pressure | B |
| Atmosphere Pressure is different from actual atmospheric pressure | C |
|
| ||||
|
| ||||
| A | |
| 13.CHECK AIR INTAKE SYSTEM |
Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.
| Result | Proceed to |
| Leaks and/or blockages exist in the intake system | A |
| No leaks or blockages in the intake system | B |
|
| ||||
| A | |
| 14.REPAIR OR REPLACE AIR INTAKE SYSTEM |
Repair or replace the malfunctioning part in the air intake system.
|
| ||||
| 15.REPLACE TURBOCHARGER SUB-ASSEMBLY |
Replace the turbocharger sub-assembly (Click here).
|
| ||||
| 16.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR |
Replace the manifold absolute pressure sensor.
|
| ||||
| 17.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 19.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 20.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.
![]() |
Take a snapshot with the intelligent tester during the Active Test.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

|
| ||||
| OK | ||
| ||
| 21.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP |
Disconnect the inlet hose from the fuel supply pump.
Operate the priming pump and check that fuel is being supplied to the fuel supply pump.
|
| ||||
| OK | |
| 22.REPLACE FUEL SUPPLY PUMP |
Replace the fuel supply pump (Click here).
|
| ||||
| 23.REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP) |
Check and repair or replace the clogged fuel pipe.
| NEXT | |
| 24.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 25.PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
| NEXT | |
| 26.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.
![]() |
Take a snapshot with the intelligent tester during the Active Test.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

| NEXT | ||
| ||
| 27.CHECK AIR INTAKE SYSTEM |
Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.
| Result | Proceed to |
| No leaks or blockages in the intake system | A |
| Leaks and/or blockages exist in the intake system | B |
|
| ||||
| A | |
| 28.INSPECT TURBOCHARGER SUB-ASSEMBLY |
Inspect the turbocharger sub-assembly (Click here).
|
| ||||
| OK | |
| 29.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EGR CUT) |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up (engine coolant temperature is 70°C (158°F) or higher), and the A/C switch and all accessory switches should be off.
Turn the ignition switch off. Wait for 30 seconds and then restart the engine.
Turn the tester on.
Select the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the MAF value displayed on the tester when engine idling.
Select the following menus: Powertrain / Engine and ECT / Active Test / Activate The VSV for EGR Cut.
Read the MAF value when the VSV for EGR cut is turned from off to on using the Active Test function.
| Active Test | Result | Proceed to |
| Activate The VSV for EGR Cut: off (Open) to on (Close) | MAF value is not changed | A |
| MAF value is changed | B |
| EGR Valve Condition (Opening) | MAF (Reference) | Measuring Condition |
| Open | 3.0 to 9.0 g/sec |
|
| Close | 15 to 22 g/sec |
|
| ||||
| A | |
| 30.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the value.
| Tester Display | Condition | Specified Condition |
| MAF | Engine not running | Below 0.3 g/sec |
|
| ||||
| OK | |
| 31.REMOVE DEPOSIT (EGR VALVE ASSEMBLY) |
Remove the EGR valve assembly.
Visually check the EGR valve assembly for deposits.
If there are deposits, clean the EGR valve assembly.
| NEXT | |
| 32.INSPECT EGR VALVE ASSEMBLY |
Inspect the EGR valve assembly (Click here).
|
| ||||
|
| ||||
| 33.REPLACE EGR VALVE ASSEMBLY |
Replace the EGR valve assembly (Click here).
|
| ||||
| 34.REPAIR OR REPLACE AIR INTAKE SYSTEM |
Repair or replace the malfunctioning part in the air intake system.
|
| ||||
| 35.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter.
|
| ||||
| 36.REPLACE TURBOCHARGER SUB-ASSEMBLY |
Replace the turbocharger sub-assembly (Click here).
| NEXT | |
| 37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 38.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the value.
| Tester Display | Condition | Specified Condition |
| MAF | Engine not running | Below 0.3 g/sec |
|
| ||||
| OK | |
| 39.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY |
Remove the exhaust manifold converter sub-assembly.
Visually check for catalyst clogging or carbon deposits adhering to the inner wall of the exhaust pipe upstream of the catalyst.
|
| ||||
|
| ||||
| 40.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter.
|
| ||||
| 41.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY |
Replace the exhaust manifold converter sub-assembly.
|
| ||||
| 42.CHECK FOR INTERMITTENT PROBLEMS |
Check for intermittent problems (Click here).
| NEXT | |
| 43.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 44.COMPARE WITH SIMILAR VEHICLE WITH SAME ENGINE |
Confirm the situation in which the lack of power was experienced by the customer again, and compare the driving feeling under the same conditions using a similar vehicle with the same engine while collecting data with the intelligent tester.
| Result | Proceed to |
| Significant difference is found | A |
| Significant difference is not found | B |
|
| ||||
| B | |
| 45.EXPLAIN THE INVESTIGATION RESULT TO CUSTOMER |
Vehicle performance is normal.
There is no problem at this point in time. However, if the problem recurs, ask the customer to explain in detail the situation in which the problem occurred.
The best course may be to have the customer ride in another vehicle with the same specifications to understand that there is no problem with the customer's vehicle.
| NEXT | ||
| ||