REAR AXLE SHAFT > INSTALLATION |
| 1. INSTALL REAR AXLE SHAFT BEARING LH |
![]() |
Using SST and a press, press in a new bearing.
| 2. INSTALL REAR AXLE SHAFT OUTER OIL SEAL |
![]() |
Using SST and a hammer, tap in a new oil seal.
| 3. INSTALL REAR AXLE HUB BOLT LH |
![]() |
Install a new gasket and the deflector to the axle shaft.
for 2WD:
Pass 5 new hub bolts through the axle hub.
for 4WD and Pre-Runner:
Pass 6 new hub bolts through the axle hub.
![]() |
Secure the axle shaft between aluminum plates in a vise.
for 2WD:
Temporarily install a washer and nut to each of the 5 hub bolts as shown in the illustration.
![]() |
for 4WD and Pre-Runner:
Temporarily install a washer and nut to each of the 6 hub bolts as shown in the illustration.
Install the hub bolts by tightening each nut.
Remove the washer and nut from each hub bolt.
| 4. INSTALL BACKING PLATE TO REAR AXLE HOUSING SETTING BOLT |
![]() |
Position the backing plate on the bearing case.
Using 2 socket wrenches and a press, press in 4 new setting bolts.
| 5. INSTALL REAR AXLE BEARING INNER RETAINER LH |
![]() |
Heat a new retainer to approximately 70 to 130°C (158 to 266°F).
Install a new shaft washer and the retainer to the axle shaft as shown in the illustration.
Using SST and a press, press in the axle shaft.
Using a snap ring expander, install a new snap ring.
| 6. INSTALL REAR AXLE BEARING INNER RETAINER LH AND REAR SKID CONTROL ROTOR (w/ ABS, VSC) |
![]() |
Using SST and a press, press in a new skid control rotor and retainer to the axle shaft until the lengths are within the standard range.
| Length A | Length B |
| 133.2 +/-0.6 mm (5.244 +/-0.0236 in.) | 56 mm (2.205 in.) |
| 7. INSTALL REAR AXLE SHAFT OIL SEAL LH |
![]() |
Using SST and a hammer, tap in a new oil seal.
| 8. INSTALL O-RING |
Install a new O-ring to the axle housing.
| 9. INSTALL REAR AXLE SHAFT WITH BACKING PLATE |
![]() |
Install the axle shaft with backing plate with the 4 nuts.
| 10. CONNECT PARKING BRAKE CABLE |
Connect the parking brake cable with the 2 bolts.
| 11. INSTALL REAR BRAKE SHOE (for 2WD) |
![]() |
Using needle-nose pliers, connect the No. 3 parking brake cable to the parking brake shoe lever.
Using needle-nose pliers, install the adjust lever tension spring to the automatic adjust lever and rear brake shoe.
![]() |
Using SST, install the shoe, pin, shoe hold down spring and shoe hold down spring cup.
| 12. INSTALL FRONT BRAKE SHOE (for 2WD) |
![]() |
Connect the shoe tension spring to the front brake shoe and rear brake shoe.
Using SST, install the shoe, shoe hold down spring and shoe hold down spring cup.
| 13. INSTALL BRAKE SHOES (for 4WD and Pre-Runner) |
![]() |
Using needle-nose pliers, connect the No. 3 parking brake cable to the parking brake shoe lever.
Install the strut set and return spring to the shoe.
![]() |
Attach the support clip to exposed threads of the strut set.
Using needle-nose pliers, hook the support clip around the spring.
Install the front and rear brake shoes.
![]() |
Move one of the shoes upward and install the shoe tension spring.
![]() |
Install the shoe front or rear side to the cylinder. Then install the other side of the shoe to the other side of the cylinder.
![]() |
Using pliers, install the front brake shoe, rear brake shoe, pins and shoe hold down springs.
| 14. INSTALL REAR SPEED SENSOR LH (w/ ABS, VSC) |
Install the speed sensor RH with the bolt.

Install the harness clamp with the bolt.
Attach the 3 clamps.
Install the speed sensor LH with the bolt.

Install the 2 harness clamps with the 2 bolts.
Attach the clamp.
Connect the sensor connector.
| 15. CONNECT BRAKE LINE (for 2WD) |
![]() |
Install the cylinder with the 2 bolts.
Using SST, connect the brake line.
| 16. CONNECT BRAKE LINE (for 4WD and Pre-Runner) |
![]() |
Install the cylinder with the 2 bolts.
Using SST, connect the brake line.
| 17. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for 2WD) |
| 18. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for 4WD and Pre-Runner) |
| 19. FILL RESERVOIR WITH BRAKE FLUID |
| 20. BLEED AIR FROM BRAKE LINE |
| 21. CHECK BRAKE FLUID LEVEL IN RESERVOIR |
| 22. CHECK FOR BRAKE FLUID LEAKAGE (for 2WD) |
| 23. CHECK FOR BRAKE FLUID LEAKAGE (for 4WD and Pre-Runner) |
| 24. INSTALL REAR WHEEL |
| 25. CHECK PARKING BRAKE LEVER TRAVEL |
Pull the lever upward with a force of approximately 200 N (20 kgf, 44 lbf) and count the number of clicks.
| 26. ADJUST PARKING BRAKE LEVER TRAVEL |
![]() |
Remove the lock nut.
Turn the No. 1 wire adjusting nut until the lever travel is correct.
Tighten the lock nut.
| 27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 28. PERFORM INITIALIZATION |
Perform initialization (Click here).
| 29. CHECK SPEED SENSOR SIGNAL |
w/ Rear Differential Lock
Check the speed sensor signal (Click here).
w/o VSC:
Check the speed sensor signal (Click here).
w/ VSC:
Check the speed sensor signal (Click here).