Home › BRAKE › BRAKE › BRAKE SYSTEM

BRAKE SYSTEM > PROBLEM SYMPTOMS TABLE

for Preparation Click here


HINT:
Use the table below to help determine the cause of the problem symptom. The potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.


Brake system (2WD LHD) 
Symptom
Suspected Area
See page
Low pedal or spongy pedal
Fluid leaks in brake system
-
Air in brake system (TMT made)
Click here
Air in brake system (TSAM made)
Click here
Piston seals (worn or damaged, TMT made)
Click here
Piston seals (worn or damaged, TSAM made)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Brake master cylinder (faulty, TMT made w/ ABS)
Click here
Brake master cylinder (faulty, TMT made w/o ABS)
Click here
Brake master cylinder (faulty, TSAM made w/ ABS)
Click here
Brake master cylinder (faulty, TSAM made w/o ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Brake drag
Brake pedal free play (minimal)
Click here
Parking brake shoe lever travel (adjustment necessary)
Click here
No. 1 parking brake wire (stuck)
Click here
No. 2 parking brake wire (stuck)
Click here
No. 3 parking brake wire (stuck)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Pad (cracked or distorted, TMT made)
Click here
Pad (cracked or distorted, TSAM made)
Click here
Lining (cracked or distorted)
Click here
Front brake piston (stuck or frozen, TMT made)
Click here
Front brake piston (stuck or frozen, TSAM made)
Click here
Rear brake piston (stuck or frozen)
Click here
Tension or return spring (faulty)
Click here
Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Vacuum leaks in booster system (TMT made)
Click here
Vacuum leaks in booster system (TSAM made)
Click here
Brake master cylinder (faulty, TMT made w/ ABS)
Click here
Brake master cylinder (faulty, TMT made w/o ABS)
Click here
Brake master cylinder (faulty, TSAM made w/ ABS)
Click here
Brake master cylinder (faulty, TSAM made w/o ABS)
Click here
Brake pull
Front brake piston (stuck or frozen, TMT made)
Click here
Front brake piston (stuck or frozen, TSAM made)
Click here
Rear brake piston (stuck or frozen)
Click here
Pad (oily, cracked or distorted, TMT made)
Click here
Pad (oily, cracked or distorted, TSAM made)
Click here
Lining (oily, cracked or distorted)
Click here
Disc (scored, TMT made)
Click here
Disc (scored, TSAM made)
Click here
Brake pedal is depressed firmly but brake is insufficient
Fluid leaks in brake system
-
Air in brake system (TMT made)
Click here
Air in brake system (TSAM made)
Click here
Pad (worn, cracked, distorted, oily or glazed, TMT made)
Click here
Pad (worn, cracked, distorted, oily or glazed, TSAM made)
Click here
Lining (worn, cracked, distorted, oily or glazed)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Disc (scored, TMT made)
Click here
Disc (scored, TSAM made)
Click here
Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Vacuum leaks in booster system (TMT made)
Click here
Vacuum leaks in booster system (TSAM made)
Click here
Noise from brakes
Pad (cracked, distorted, dirty or glazed, TMT made)
Click here
Pad (cracked, distorted, dirty or glazed, TSAM made)
Click here
Lining (cracked, distorted, dirty or glazed)
Click here
Installation bolt (TMT made)
Click here
Installation bolt (TSAM made)
Click here
Disc (scored, TMT made)
Click here
Disc (scored, TSAM made)
Click here
Pad support plate (loose, TMT made)
Click here
Pad support plate (loose, TSAM made)
Click here
Anchor, return or tension spring (faulty)
Click here
Anti squeal shim (damaged, TMT made)
Click here
Anti squeal shim (damaged, TSAM made)
Click here
Shoe hold down spring (damaged)
Click here

Brake system (2WD RHD) 
Symptom
Suspected Area
See page
Low pedal or spongy pedal
Fluid leaks in brake system
-
Air in brake system (TMT made)
Click here
Air in brake system (TSAM made)
Click here
Piston seals (worn or damaged, TMT made)
Click here
Piston seals (worn or damaged, TSAM made)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Brake master cylinder (faulty, TMT made w/ ABS)
Click here
Brake master cylinder (faulty, TMT made w/o ABS)
Click here
Brake master cylinder (faulty, TSAM made w/ ABS)
Click here
Brake master cylinder (faulty, TSAM made w/o ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Brake drag
Brake pedal free play (minimal)
Click here
Parking brake shoe lever travel (adjustment necessary)
Click here
No. 1 parking brake wire (stuck)
Click here
No. 2 parking brake wire (stuck)
Click here
No. 3 parking brake wire (stuck)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Pad (cracked or distorted, TMT made)
Click here
Pad (cracked or distorted, TSAM made)
Click here
Lining (cracked or distorted)
Click here
Front brake piston (stuck or frozen, TMT made)
Click here
Front brake piston (stuck or frozen, TSAM made)
Click here
Rear brake piston (stuck or frozen)
Click here
Tension or return spring (faulty)
Click here
Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Vacuum leaks in booster system (TMT made)
Click here
Vacuum leaks in booster system (TSAM made)
Click here
Brake master cylinder (faulty, TMT made w/ ABS)
Click here
Brake master cylinder (faulty, TMT made w/o ABS)
Click here
Brake master cylinder (faulty, TSAM made w/ ABS)
Click here
Brake master cylinder (faulty, TSAM made w/o ABS)
Click here
Brake pull
Front brake piston (stuck or frozen, TMT made)
Click here
Front brake piston (stuck or frozen, TSAM made)
Click here
Rear brake piston (stuck or frozen)
Click here
Pad (oily, cracked or distorted, TMT made)
Click here
Pad (oily, cracked or distorted, TSAM made)
Click here
Lining (oily, cracked or distorted)
Click here
Disc (scored, TMT made)
Click here
Disc (scored, TSAM made)
Click here
Brake pedal is depressed firmly but brake is insufficient
Fluid leaks in brake system
-
Air in brake system (TMT made)
Click here
Air in brake system (TSAM made)
Click here
Pad (worn, cracked, distorted, oily or glazed, TMT made)
Click here
Pad (worn, cracked, distorted, oily or glazed, TSAM made)
Click here
Lining (worn, cracked, distorted, oily or glazed)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Disc (scored, TMT made)
Click here
Disc (scored, TSAM made)
Click here
Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Vacuum leaks in booster system (TMT made)
Click here
Vacuum leaks in booster system (TSAM made)
Click here
Noise from brakes
Pad (cracked, distorted, dirty or glazed, TMT made)
Click here
Pad (cracked, distorted, dirty or glazed, TSAM made)
Click here
Lining (cracked, distorted, dirty or glazed)
Click here
Installation bolt (TMT made)
Click here
Installation bolt (TSAM made)
Click here
Disc (scored, TMT made)
Click here
Disc (scored, TSAM made)
Click here
Pad support plate (loose, TMT made)
Click here
Pad support plate (loose, TSAM made)
Click here
Anchor, return or tension spring (faulty)
Click here
Anti squeal shim (damaged, TMT made)
Click here
Anti squeal shim (damaged, TSAM made)
Click here
Shoe hold down spring (damaged)
Click here

Brake system (4WD LHD) 
Symptom
Suspected Area
See page
Low pedal or spongy pedal
Fluid leaks in brake system
-
Air in brake system (TMT made)
Click here
Air in brake system (TSAM made)
Click here
Piston seals (worn or damaged, TMT made)
Click here
Piston seals (worn or damaged, TSAM made)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Brake master cylinder (faulty, TMT made w/ ABS)
Click here
Brake master cylinder (faulty, TMT made w/o ABS)
Click here
Brake master cylinder (faulty, TSAM made w/ ABS)
Click here
Brake master cylinder (faulty, TSAM made w/o ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Brake drag
Brake pedal free play (minimal)
Click here
Parking brake shoe lever travel (adjustment necessary)
Click here
No. 1 parking brake wire (stuck)
Click here
No. 2 parking brake wire (stuck)
Click here
No. 3 parking brake wire (stuck)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Pad (cracked or distorted, TMT made)
Click here
Pad (cracked or distorted, TSAM made)
Click here
Lining (cracked or distorted)
Click here
Front brake piston (stuck or frozen, TMT made)
Click here
Front brake piston (stuck or frozen, TSAM made)
Click here
Rear brake piston (stuck or frozen)
Click here
Tension or return spring (faulty)
Click here
Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Vacuum leaks in booster system (TMT made)
Click here
Vacuum leaks in booster system (TSAM made)
Click here
Brake master cylinder (faulty, TMT made w/ ABS)
Click here
Brake master cylinder (faulty, TMT made w/o ABS)
Click here
Brake master cylinder (faulty, TSAM made w/ ABS)
Click here
Brake master cylinder (faulty, TSAM made w/o ABS)
Click here
Brake pull
Front brake piston (stuck or frozen, TMT made)
Click here
Front brake piston (stuck or frozen, TSAM made)
Click here
Rear brake piston (stuck or frozen)
Click here
Pad (oily, cracked or distorted, TMT made)
Click here
Pad (oily, cracked or distorted, TSAM made)
Click here
Lining (oily, cracked or distorted)
Click here
Disc (scored, TMT made)
Click here
Disc (scored, TSAM made)
Click here
Brake pedal is depressed firmly but brake is insufficient
Fluid leaks in brake system
-
Air in brake system (TMT made)
Click here
Air in brake system (TSAM made)
Click here
Pad (worn, cracked, distorted, oily or glazed, TMT made)
Click here
Pad (worn, cracked, distorted, oily or glazed, TSAM made)
Click here
Lining (worn, cracked, distorted, oily or glazed)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Disc (scored, TMT made)
Click here
Disc (scored, TSAM made)
Click here
Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Vacuum leaks in booster system (TMT made)
Click here
Vacuum leaks in booster system (TSAM made)
Click here
Noise from brakes
Pad (cracked, distorted, dirty or glazed, TMT made)
Click here
Pad (cracked, distorted, dirty or glazed, TSAM made)
Click here
Lining (cracked, distorted, dirty or glazed)
Click here
Installation bolt (TMT made)
Click here
Installation bolt (TSAM made)
Click here
Disc (scored, TMT made)
Click here
Disc (scored, TSAM made)
Click here
Anchor, return or tension spring (faulty)
Click here
Anti squeal shim (damaged, TMT made)
Click here
Anti squeal shim (damaged, TSAM made)
Click here
Shoe hold down spring (damaged)
Click here

Brake system (4WD RHD) 
Symptom
Suspected Area
See page
Low pedal or spongy pedal
Fluid leaks in brake system
-
Air in brake system (TMT made)
Click here
Air in brake system (TSAM made)
Click here
Piston seals (worn or damaged, TMT made)
Click here
Piston seals (worn or damaged, TSAM made)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Brake master cylinder (faulty, TMT made w/ ABS)
Click here
Brake master cylinder (faulty, TMT made w/o ABS)
Click here
Brake master cylinder (faulty, TSAM made w/ ABS)
Click here
Brake master cylinder (faulty, TSAM made w/o ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Brake drag
Brake pedal free play (minimal)
Click here
Parking brake shoe lever travel (adjustment necessary)
Click here
No. 1 parking brake wire (stuck)
Click here
No. 2 parking brake wire (stuck)
Click here
No. 3 parking brake wire (stuck)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Pad (cracked or distorted, TMT made)
Click here
Pad (cracked or distorted, TSAM made)
Click here
Lining (cracked or distorted)
Click here
Front brake piston (stuck or frozen, TMT made)
Click here
Front brake piston (stuck or frozen, TSAM made)
Click here
Rear brake piston (stuck or frozen)
Click here
Tension or return spring (faulty)
Click here
Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Vacuum leaks in booster system (TMT made)
Click here
Vacuum leaks in booster system (TSAM made)
Click here
Brake master cylinder (faulty, TMT made w/ ABS)
Click here
Brake master cylinder (faulty, TMT made w/o ABS)
Click here
Brake master cylinder (faulty, TSAM made w/ ABS)
Click here
Brake master cylinder (faulty, TSAM made w/o ABS)
Click here
Brake pull
Front brake piston (stuck or frozen, TMT made)
Click here
Front brake piston (stuck or frozen, TSAM made)
Click here
Rear brake piston (stuck or frozen)
Click here
Pad (oily, cracked or distorted, TMT made)
Click here
Pad (oily, cracked or distorted, TSAM made)
Click here
Lining (oily, cracked or distorted)
Click here
Disc (scored, TMT made)
Click here
Disc (scored, TSAM made)
Click here
Brake pedal is depressed firmly but brake is insufficient
Fluid leaks in brake system
-
Air in brake system (TMT made)
Click here
Air in brake system (TSAM made)
Click here
Pad (worn, cracked, distorted, oily or glazed, TMT made)
Click here
Pad (worn, cracked, distorted, oily or glazed, TSAM made)
Click here
Lining (worn, cracked, distorted, oily or glazed)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Disc (scored, TMT made)
Click here
Disc (scored, TSAM made)
Click here
Booster push rod (adjustment necessary, TMT made w/ ABS)
Click here
Booster push rod (adjustment necessary, TMT made w/o ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/ ABS)
Click here
Booster push rod (adjustment necessary, TSAM made w/o ABS)
Click here
Vacuum leaks in booster system (TMT made)
Click here
Vacuum leaks in booster system (TSAM made)
Click here
Noise from brakes
Pad (cracked, distorted, dirty or glazed, TMT made)
Click here
Pad (cracked, distorted, dirty or glazed, TSAM made)
Click here
Lining (cracked, distorted, dirty or glazed)
Click here
Installation bolt (TMT made)
Click here
Installation bolt (TSAM made)
Click here
Disc (scored, TMT made)
Click here
Disc (scored, TSAM made)
Click here
Anchor, return or tension spring (faulty)
Click here
Anti squeal shim (damaged, TMT made)
Click here
Anti squeal shim (damaged, TSAM made)
Click here
Shoe hold down spring (damaged)
Click here

Brake system (Pre-runner) 
Symptom
Suspected Area
See page
Low pedal or spongy pedal
Fluid leaks in brake system
-
Air in brake system
Click here
Piston seals (worn or damaged)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Brake master cylinder (faulty, w/ ABS)
Click here
Brake master cylinder (faulty, w/o ABS)
Click here
Booster push rod (adjustment necessary, w/ ABS)
Click here
Booster push rod (adjustment necessary, w/o ABS)
Click here
Brake drag
Brake pedal free play (minimal)
Click here
Parking brake shoe lever travel (adjustment necessary)
Click here
No. 1 parking brake wire (stuck)
Click here
No. 2 parking brake wire (stuck)
Click here
No. 3 parking brake wire (stuck)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Pad (cracked or distorted)
Click here
Lining (cracked or distorted)
Click here
Front brake piston (stuck or frozen)
Click here
Rear brake piston (stuck or frozen)
Click here
Tension or return spring (faulty)
Click here
Booster push rod (adjustment necessary, w/ ABS)
Click here
Booster push rod (adjustment necessary, w/o ABS)
Click here
Vacuum leaks in booster system
Click here
Brake master cylinder (faulty, w/ ABS)
Click here
Brake master cylinder (faulty, w/o ABS)
Click here
Brake pull
Front brake piston (stuck or frozen)
Click here
Rear brake piston (stuck or frozen)
Click here
Pad (oily, cracked or distorted)
Click here
Lining (oily, cracked or distorted)
Click here
Disc (scored)
Click here
Brake pedal is depressed firmly but brake is insufficient
Fluid leaks in brake system
-
Air in brake system
Click here
Pad (worn, cracked, distorted, oily or glazed)
Click here
Lining (worn, cracked, distorted, oily or glazed)
Click here
Rear brake shoe clearance (adjustment necessary)
Click here
Disc (scored)
Click here
Booster push rod (adjustment necessary, w/ ABS)
Click here
Booster push rod (adjustment necessary, w/o ABS)
Click here
Vacuum leaks in booster system
Click here
Noise from brakes
Pad (cracked, distorted, dirty or glazed)
Click here
Lining (cracked, distorted, dirty or glazed)
Click here
Installation bolt
Click here
Disc (scored)
Click here
Anchor, return or tension spring (faulty)
Click here
Anti squeal shim (damaged)
Click here
Shoe hold down spring (damaged)
Click here