Home › TRANSMISSION ยท A343F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Inspect the torque converter clutch assembly (Click here ).



2. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY


D025544E01
  1. Install the torque converter clutch to the automatic transmission.

  1. Using a vernier caliper and straightedge, measure dimension A between the transmission and the end surface of the drive plate.



    D025545E01
  1. Using a vernier caliper and straightedge, measure dimension B shown in the illustration. Check that B is greater than A.

    Standard dimension:
    B = A + 1.00 mm (0.0394 in.) or more



3. INSTALL TRANSFER ASSEMBLY
  1. Install the transfer assembly (Click here).



4. INSTALL NO. 1 ENGINE MOUNTING INSULATOR REAR


G034260E01
  1. Install the engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



5. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


G039174E01
  1. Install the transmission to the engine with the 7 bolts.

    Torque:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf } for 17mm head
    37 N*m{ 377 kgf*cm , 27 ft.*lbf } for 14 mm head



    C118034E01
  1. Install the exhaust manifold stay with the 3 bolts.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for bolt A
    30 N*m{ 306 kgf*cm , 22 ft.*lbf } for bolt B
    71 N*m{ 724 kgf*cm , 52 ft.*lbf } for bolt C



    G034529E01
  1. Hold the crankshaft pulley bolt with a wrench and install the 6 torque converter clutch mounting bolts.

    Torque:
    41 N*m{ 418 kgf*cm , 30 ft.*lbf }



6. INSTALL FLYWHEEL HOUSING DUST SEAL


7. CONNECT WIRE HARNESS


8. CONNECT CONNECTOR
  1. Transmission side:
    Connect the connectors.

    1. Connect the temperature sensor connector.

    2. Connect the park/neutral position switch connector.

    3. Connect the 2 speed sensor connectors.

    4. Connect the transmission wire connector.

  1. Transfer side:
    Connect the connectors.

    1. Connect the indicator switch connector (for 4WD).

    2. Connect the speedometer sensor connector.

    3. Connect the indicator switch connector (for L4).

    4. Connect the indicator switch connector (neutral).



9. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


G034256E01
  1. *1: Install the 4 set bolts of the engine mounting insulator.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

  1. *2: Install the frame crossmember with the 4 bolts and 4 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



10. INSTALL STARTER ASSEMBLY


    G039103E03
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Install the starter wire to terminal 30 with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the starter connector.



11. INSTALL FRONT FENDER SEAL
  1. Install the fender seal with the 5 clips.



12. INSTALL TRANSMISSION CONTROL CABLE BRACKET


G034516E01
  1. Install the control cable bracket with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



13. CONNECT TRANSMISSION CONTROL SHIFT CABLE ASSEMBLY


G034515E01
  1. Connect the control cable with the clip.

  1. Connect the control cable with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



14. INSTALL OIL COOLER TUBE


C118032E01
  1. Loosely install the tip of the oil cooler tube inlet to the automatic transmission by hand.

  1. Loosely install the tip of the oil cooler tube outlet to the automatic transmission by hand.

  1. Install the 3 clamps with the 3 bolts.

    Torque:
    5.0 N*m{ 50 kgf*cm , 44 in.*lbf } for A
    12 N*m{ 122 kgf*cm , 9 ft.*lbf } for B



    C118036E02
  1. Using a union nut wrench, tighten the inlet and outlet tubes.

    Torque:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf } for use without union nut wrench
    31 N*m{ 316 kgf*cm , 23 ft.*lbf } for use with union nut wrench

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



15. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


C118024
  1. Coat a new O-ring with ATF, and install it to the oil filler tube.

  1. Install the oil filler tube with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Install the oil dipstick.



16. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
  1. Install the propeller with center bearing shaft assembly (Click here).



17. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
  1. Install the front propeller shaft assembly (Click here).



18. INSTALL TRANSFER CASE LOWER PROTECTOR
  1. Install the transfer case lower protector with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



19. INSTALL FRONT EXHAUST PIPE ASSEMBLY


A107610
  1. Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    40 mm (1.57 in.)

    If the length is less than the minimum, replace the compression spring.

  1. Install the front pipe to the pipe support.



    A099436E03
  1. Install a new gasket to the exhaust manifold.

    HINT:
    Using a plastic-faced hammer, uniformly strike the gasket so that the gasket and exhaust manifold are properly fit.

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    2. Do not reuse the gasket.
    3. To ensure a proper seal, do not use the front pipe to force the gasket onto the exhaust manifold.

  1. Install the front pipe with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A169038
  1. Attach the 3 wire clamps to the vehicle body.

  1. Connect the heated oxygen sensor connector.

  1. Connect the front pipe to the center pipe with a new gasket, 2 bolts and 2 nuts. Alternately tighten the bolts in several passes.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    Do not reuse the gasket.



20. INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY


C113710E02
  1. Install the transfer shift lever to the shift lever retainer.

  1. Using needle-nose pliers, install the snap ring.

  1. Install the shift lever boot with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    HINT:
    Apply MP grease to the tip of the transfer shift lever.



21. INSTALL SHIFT LEVER BOOT ASSEMBLY
  1. Install the shift lever boot with the 4 screws.



22. ADJUST SHIFT LEVER POSITION


G034515E01
  1. Remove the nut and disconnect the control cable.

  1. Remove the clip and disconnect the control cable from the control cable bracket.



    D028682E01
  1. Push the control shaft rearward as much as possible.

  1. Return the control shaft lever 2 notches to the N position.

  1. While holding the control shaft lever slightly toward the R position side, tighten the nut.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }



23. ADD AUTOMATIC TRANSMISSION FLUID

Fluid type:
Toyota Genuine ATF Type T-IV



24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


25. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



26. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves rearward after shifting to R.
    If the results are not as specified, inspect the park/neutral position switch and check the shift lever.



27. INSTALL CONSOLE BOX ASSEMBLY


B090153E01
  1. Install the console box with the 2 clips, 4 screws <F> and 2 bolts <E>.



28. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


B115418E02

NOTICE:
Be careful not to damage the instrument panel lower and console box with the claws of the console panel upper.

  1. Attach the 12 claws to install the console panel.



29. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY


B087844E02
  1. Attach the 4 claws to install the hole cover.



30. CHECK FOR EXHAUST GAS LEAKS


31. INSPECT AUTOMATIC TRANSMISSION FLUID
  1. Inspect the automatic transmission fluid (Click here).



32. INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }



33. INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }