Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY (for 1GR-FE)

AUTOMATIC TRANSMISSION ASSEMBLY (for 1GR-FE) > INSTALLATION

for Preparation Click here



1. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Inspect the torque converter clutch assembly (Click here).



2. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Install the torque converter clutch to the automatic transmission.



    C193529E01
  1. Using a vernier caliper and straightedge, measure dimension A between the contact surfaces of the transmission and engine *1, and the contact surfaces of the converter and drive plate *2. (#)



    C193531E01
  1. Using a vernier caliper and straightedge, measure dimension B shown in the illustration. Check that B is greater than A measured in step (#).

    Standard:
    B = A + 1.00 mm (0.0394 in.) or more



3. INSTALL TRANSFER ASSEMBLY
  1. Install the transfer assembly (Click here).



4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


C193851E01
  1. Apply clutch spline grease to the round of the crankshaft contact surface with the torque converter clutch centerpiece.

    Clutch spline grease:
    Toyota Genuine Clutch Spline Grease or equivalent
    Maximum grease amount:
    Approximately 1 g (0.353 oz)



    C196678E01
  1. Install the transmission to the engine with the 9 bolts.

    Torque:
    for bolt A:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }
    for bolt B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    NOTICE:
    Confirm 2 knock pins are on the transmission fitting surface of the engine block before the transmission installation.



    C111234
  1. Hold the crankshaft pulley bolt with a wrench and install the 6 torque converter clutch mounting bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    HINT:
    First install the black bolt, and then the other 5 bolts.



5. INSTALL FLYWHEEL HOUSING SIDE COVER


6. INSTALL STARTER ASSEMBLY
  1. Install starter assembly (Click here).



7. CONNECT WIRE HARNESS


8. CONNECT CONNECTOR
  1. Transmission side:
    Connect the connectors.

    1. Connect the park/neutral position switch connector.

    2. Connect the transmission wire connector.

    3. Connect the 2 speed sensor connectors.

  1. Transfer side:
    Connect the connectors.

    1. Connect the No. 1 indicator switch connector.

    2. Connect the No. 2 indicator switch connector.

    3. Connect the speed sensor connector.



9. INSTALL NO. 1 ENGINE MOUNTING INSULATOR REAR


G034260E01
  1. Install the engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



10. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


G034256E01
  1. *1: Install the frame crossmember to the engine mounting insulator with the 4 set bolts.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

  1. *2: Connect the ends of the frame crossmember to the vehicle with the 4 bolts and 4 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



11. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET


C111232
  1. Install the control cable bracket with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



12. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


C111231
  1. Connect the control cable with the clip.

  1. Connect the control cable with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



13. INSTALL OIL COOLER TUBE


C111230
  1. Loosely install the tip of the oil cooler tube inlet to the automatic transmission by hand.

  1. Loosely install the tip of the oil cooler tube outlet to the automatic transmission by hand.

  1. Install the 2 clamps with the 2 bolts.

    Torque:
    5.0 N*m{ 50 kgf*cm , 43 in.*lbf }



    C112850E03
  1. Using a union nut wrench, tighten the oil cooler inlet and outlet tubes.

    Torque:
    for use without union nut wrench:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf }
    for use with union nut wrench:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).
    2. The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.



14. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A076440E02
  1. Set a new gasket to the RH cylinder head with the oval shape facing forward.

    NOTICE:
    Be careful of the installation direction.

  1. Install the exhaust manifold with the 6 nuts. Uniformly tighten the nuts in several passes.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the A/F sensor connector.



15. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A076439E01
  1. Set a new gasket to the LH cylinder head with the oval shape facing backward.

    NOTICE:
    Be careful of the installation direction.

  1. Install the exhaust manifold with the 6 nuts. Uniformly tighten the nuts in several passes.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the A/F sensor connector.



16. INSTALL NO. 2 MANIFOLD STAY


F050356E01
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



17. INSTALL MANIFOLD STAY


F050360E01
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



18. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
  1. for TSAM Made:
    Install the propeller shaft with center bearing assembly (Click here).

  1. for TMT Made:
    Install the propeller shaft with center bearing assembly (Click here).



19. INSTALL EXHAUST PIPE
  1. Install the exhaust pipe (Click here).



20. CONNECT HEATED OXYGEN SENSOR


21. INSTALL TRANSFER CASE LOWER PROTECTOR
  1. Install the protector with the 4 bolts.

    Torque:
    18 N*m{ 283 kgf*cm , 13 ft.*lbf }



22. INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY


C113710E02
  1. Install the transfer shift lever to the shift lever retainer.

  1. Using needle-nose pliers, install the snap ring.

  1. Install the transfer high and low shift lever with the 4 bolts.

    Torque:
    18 N*m{ 283 kgf*cm , 13 ft.*lbf }



23. INSTALL SHIFT LEVER BOOT ASSEMBLY
  1. Install the shift lever boot with the 4 screws.



24. INSTALL CONSOLE BOX ASSEMBLY


B090153E01
  1. Install the console box with the 2 clips, 4 screws <F> and 2 bolts <E>.



25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



26. ADD AUTOMATIC TRANSMISSION FLUID
  1. Add automatic transmission fluid (Click here).



27. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch to ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves in reverse after shifting to R.
    If the results are not as specified, inspect the park/ neutral position switch and check the shift lever.



28. PERFORM INITIALIZATION
  1. Perform initialization (Click here).



29. CHECK FOR EXHAUST GAS LEAKS


30. INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m{ 285 kgf*cm , 21 ft.*lbf }



31. INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m{ 285 kgf*cm , 21 ft.*lbf }