OIL PUMP (w/ EGR Cooler) > INSTALLATION |
| 1. INSTALL TIMING GEAR CASE ASSEMBLY |
![]() |
Install 2 new O-rings to the cylinder block.
Remove any old seal packing (FIPG) material from the timing gear case and cylinder block.
![]() |
Set a new oil pump gasket to the timing gear case.
![]() |
Apply seal packing to the areas shown in the illustration.
![]() |
Install the timing gear case with the 8 bolts and union bolt labeled A shown in the illustration.
Make sure that the oil pump drive gear rotates smoothly.
If the gear does not rotate smoothly, remove the 8 bolts and union bolt to release the gear. Then install the bolts and gear again.
Install the No. 1 vacuum transmitting pipe with the nut.
| 2. INSTALL OIL PAN SUB-ASSEMBLY |
Install a new gasket and the oil strainer with the 2 bolts and nut.
Remove old seal packing (FIPG) from the oil pan and cylinder block.
![]() |
Apply seal packing to the areas shown in the illustration.
Install the oil pan with the 22 bolts and 2 nuts.
| 3. INSTALL OIL DIPSTICK GUIDE |
![]() |
Install a new O-ring to the guide.
Apply a small amount of clean engine oil to the O-ring.
Install the guide with the bolt.
Install the injection pipe clamp with the bolt.
| 4. INSTALL FUEL SUPPLY PUMP ASSEMBLY |
![]() |
Check that the supply pump gear in the timing gear case moves back and forth smoothly.
Install a new O-ring to the pump.
Apply a light coat of engine oil to the O-ring.
![]() |
Align the set key on the drive shaft with the groove of the injection gear.
![]() |
Install the pump with the 2 nuts.
Set a new O-ring.
![]() |
Using SST, hold the crankshaft pulley and install the set nut.
![]() |
Using a dial indicator, measure the thrust clearance of the injection pump shaft by moving the pump drive shaft pulley back and forth.
![]() |
Connect the 2 connectors.
![]() |
Connect the 2 fuel hoses.
| 5. INSTALL INJECTION GEAR |
Set a new O-ring and then temporarily install the nut. Using your hand, check the thrust clearance of the supply pump drive shaft by driving the injection gear.
| 6. INSTALL CRANKSHAFT TIMING GEAR |
![]() |
Face the crankshaft timing gear with timing mark 1 facing the forward.
Align the set key on the crankshaft with the key groove of the crankshaft timing gear.
Using SST and a hammer, tap in the timing gear.
| 7. INSTALL NO. 1 IDLE GEAR |
![]() |
Install the gear shaft as shown in the illustration.
![]() |
Apply light coat engine oil to the No. 1 idler gear shaft shown in the illustration.
![]() |
Align the "5" timing marks of the idle gear and crankshaft timing gear.
Using SST, turn the supply pump gear, and align the "4" timing marks of the idle gear and injection gear, and mesh the gears.
![]() |
Temporarily install the No. 1 idle gear with the idle gear thrust plate and 2 bolts.
Secure the idle gears to the idle gear the service bolt.
Tighten the No. 1 idle gear with the 2 bolts.
Remove the service bolt.
![]() |
Install the No. 1 crankshaft angle sensor plate.
| 8. INSTALL TIMING GEAR COVER |
![]() |
Install a new O-ring to the timing gear case.
Remove any old seal packing (FIPG) material from the timing gear cover.
![]() |
Apply seal packing to the areas shown in the illustration.
![]() |
Install the cover with the 14 bolts and 2 nuts.
| 9. INSTALL CRANKSHAFT POSITION SENSOR |
Install the crankshaft position sensor with the bolt.
| 10. INSTALL CAMSHAFT POSITION SENSOR |
Install the camshaft position sensor with the bolt.
| 11. INSTALL CRANKSHAFT PULLEY |
![]() |
Align the pulley set key with the key groove of the pulley.
Using SST, install the pulley bolt.
| 12. INSTALL PUMP DRIVE SHAFT PULLEY |
Install a new O-ring to the supply pump.
Temporarily install the supply pump with the nut.
![]() |
Using SST, hold the crankshaft pulley and tighten the nut.
![]() |
Install the camshaft timing pulley flange No. 2 and pump drive shaft pulley with the 4 bolts.
![]() |
Move the pump drive shaft pulley back and forth to check the thrust clearance of the pump drive shaft.
| 13. INSTALL VANE PUMP ASSEMBLY |
Install a new O-ring to the vane pump.
Install the vane pump with the 2 nuts.
| 14. INSTALL VACUUM PUMP ASSEMBLY |
Install 2 new O-rings to the vacuum pump.
Install the vacuum pump with the 2 nuts.
| 15. INSTALL TIMING GEAR COVER INSULATOR |
Install the gear cover insulator with the bolt.
| 16. INSTALL WATER PUMP ASSEMBLY |
![]() |
Install a new gasket and the water pump with the 5 bolts and 2 nuts.
| 17. INSTALL CYLINDER BLOCK INSULATOR |
![]() |
Install the block insulator to the head.
| 18. INSTALL NO. 2 TIMING BELT COVER |
![]() |
Apply seal packing (FIPG) to the specified areas shown in the illustration.
Install the No. 2 timing belt cover with the 4 bolts and nut.
| 19. INSTALL CAMSHAFT TIMING PULLEY |
![]() |
Install the camshaft timing pulley.
Fasten the bolt of the camshaft timing pulley by holding the camshaft with a wrench.
| 20. INSTALL TIMING BELT |
![]() |
Check that the timing marks are aligned as shown in the illustration.
Using a 10 mm hexagon wrench, install the timing belt idler pulley and new washer with the bolt.
Check that the idler pulley moves smoothly.
If it does not move smoothly, check the idler sub-assembly and washer.
Install the timing belt to the pump drive shaft pulley, camshaft timing pulley and No. 1 timing belt idler in sequence.
![]() |
Place the tensioner upright. Then set the press to the top of the tensioner.
Using a press, slowly push in the push rod using 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) of force.
Align the holes of the push rod and housing. Then pass a 1.27 mm hexagon wrench through the holes to keep the setting position of the push rod.
Install the timing belt tensioner with the 2 bolts while pushing the idler pulley toward the timing belt.
Tighten the 2 bolts.
![]() |
Remove the 1.5 mm hexagon wrench from the tensioner.
![]() |
Turn the crankshaft clockwise 720° and check that the timing marks are aligned as shown in the illustration.
| 21. INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY |
| 22. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
Remove any old seal packing (FIPG) material from the cylinder head.
![]() |
Apply seal packing to the specific areas shown in the illustration.
![]() |
Install a new cylinder head cover gasket and the cylinder head cover with the 10 bolts and 2 nuts.
Install 4 new nozzle holder seals.
Connect the ventilation hose.
![]() |
Connect the 4 connectors and install the 3 bolts.
| 23. INSTALL VENTILATION PIPE |
![]() |
Connect the ventilation pipe to the cylinder head cover, and then install the bolt to the pipe.
| 24. INSTALL NO. 4 INJECTION PIPE |
![]() |
Temporarily install the No. 4 injection pipe with the union nuts.
Install the bolt.
![]() |
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a union nut wrench, tighten the injection pipe union nuts on the injector side.
| 25. INSTALL EGR COOLER WITH ELECTRIC EGR CONTROL VALVE AND NO. 2 EGR VALVE |
install the EGR cooler with electric EGR control valve and No. 2 EGR valve (Click here).
| 26. INSTALL FUEL INLET PIPE SUB-ASSEMBLY |
![]() |
Temporarily install the fuel inlet pipe with the union nuts.
) Install a new O-ring to the oil level gauge guide, and install the oil level gauge guide to the cylinder block.
![]() |
Temporarily install the stay of the oil level gauge guide to the intake manifold with the bolt.
![]() |
Install the clamp with the bolt.
Tighten the bolt of the oil level gauge guide stay.
![]() |
Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nut on the supply pump side.
| 27. INSTALL ENGINE ASSEMBLY |
Install the engine (Click here).
| 28. ADD ENGINE OIL |
Wipe the oil pan and drain plug.
Install a new gasket and the drain plug.
Add new oil.
| Item | Specified Condition |
| Drain and refill with oil filter change | 6.9 liters (7.3 US qts, 6.1 Imp. qts) |
| Drain and refill without oil filter change | 6.6 liters (7.0 US qts, 5.8 Imp. qts) |
| Dry fill | 7.4 liters (7.8 US qts, 6.5 Imp. qts) |
Install the oil filler cap.
| 29. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Start the engine.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| 30. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 31. PERFORM REGISTRATION |
Perform registration of the injector compensation codes .
Perform pilot quantity learning .
| 32. INSPECT ENGINE OIL LEVEL |
| 33. INSPECT FOR FUEL LEAK |
![]() |
Check that there are no leaks from any part of the fuel system when the engine is stopped.
If there is fuel leakage, repair or replace parts as necessary.
Start the engine and check that there are no leaks from any part of the fuel system.
If there is fuel leakage, repair or replace parts as necessary.
Disconnect the return hose from the common rail.
Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.
Connect the intelligent tester to the DLC3.
Start the engine and push the intelligent tester main switch ON.
Select the Fuel Leak test from the Active Test mode on the intelligent tester.
If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.
Check that there are no leaks from any part of the fuel system.
Reconnect the return hose to the common rail.
| 34. INSPECT FOR ENGINE OIL LEAK |
| 35. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester to the radiator reservoir.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2 ,17.1 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks.
If no external leaks are found, check the cylinder block and head.