Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM (w/ VSC)

CAN COMMUNICATION SYSTEM (w/ VSC) > Check CAN Bus Lines for Short Circuit


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
  1. Short between CAN bus lines
  2. Brake actuator assembly (skid control ECU)
  3. Spiral cable (steering angle sensor)
  4. Yaw rate sensor
  5. ECM
  6. No. 1 junction connector
  7. No. 2 junction connector
  8. No. 3 junction connector

WIRING DIAGRAM


C190675E04


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)


    H102621E28
  1. Disconnect the J49 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    D1-6 (CANH) - D1-14 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3.CONNECT CONNECTOR
  1. Reconnect the J49 No. 3 junction connector connector.


NEXT


4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)


    H102621E28
  1. Disconnect the J54 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 9
OK


5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)


    C190787E05
  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J54-13 (CANH) - J54-7 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
Go to step 7
OK


6.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM)


    C190787E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J54-12 (CANH) - J54-6 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 8
OK

REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR 

7.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)


    C190787E05
  1. Disconnect the S35 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Result
    Proceed to
    J54-13 (CANH) - J54-7 (CANL)
    Ignition switch off
    1 Ω or higher
    OK (for LHD)
    A
    OK (for RHD)
    B
    Below 1 Ω
    NG
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)

C
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
A

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)  

8.CHECK FOR SHORT IN CAN BUS WIRES (ECM)


    C190787E06
  1. Disconnect the E6 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J54-12 (CANH) - J54-6 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    Below 1 Ω
    NG



B
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)  

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C190788E05
  1. Disconnect the J53 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J53-1 (CANH) - J53-2 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


10.CONNECT CONNECTOR
  1. Reconnect the J54 No. 1 junction connector connector.


NEXT


11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)
H102621E28
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 14
OK


12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR)


    C190788E06
  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J53-4 (CANH) - J53-6 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
Go to step 13
OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR 

13.CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR)


    C190788E06
  1. Disconnect the Y1 yaw rate sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

Result 
Tester Connection
Switch Condition
Measured Resistance
Proceed to
J53-4 (CANH) - J53-6 (CANL)
Ignition switch off
1 Ω or higher
OK
Below 1 Ω
NG


NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CANH, CANL)
OK

REPLACE YAW RATE SENSOR (Click here)  

14.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C190789E06
  1. Disconnect the J50 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J50-2 (CANH) - J50-1 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


15.CONNECT CONNECTOR
  1. Reconnect the J53 No. 2 junction connector connector.

  1. Reconnect the J50 No. 3 junction connector connector.


NEXT


16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    C190789E07
  1. Disconnect the J51 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J51-2 (CANH) - J51-1 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
Go to step 17
OK

REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR 

17.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)


    C190789E07
  1. Disconnect the S37 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J51-2 (CANH) - J51-1 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE SPIRAL CABLE (STEERING ANGLE SENSOR) (Click here)