Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/ EGR Cooler)

DTC    P0622    Generator Field "F" Terminal Circuit

for Preparation Click here


DESCRIPTION

While the generator is generating current, a duty signal is sent from terminal M of the generator to the ECM terminal ALT. The duty signal indicates density of field current flowing through the rotor coil of the generator, and the ratio of the duty signal is high when the voltage generated from the generator is high. The ECM uses this duty signal to determine if the generator is operating.
The ECM will detect a generator failure or an open malfunction of the circuit, if the duty signal is not output from terminal M of the generator, although the engine is running.

A190931E01


DTC No.
DTC Detection Condition
Trouble Area
P0622
No duty signal from terminal M of generator at engine running
(1 trip detection logic)
  1. Open in generator circuit
  2. Generator
  3. ECM

WIRING DIAGRAM


A194472E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0622)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menu: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0622
    A
    P0622 and other DTCs
    B



B
GO TO DTC CHART (Click here)
A


2.CHECK WHETHER DTC OUTPUT RECURS (DTC P0622)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menu: Powertrain / Engine / DTC / Clear.

  1. Clear DTCs.

  1. Start the engine.

  1. Allow the engine to idle for 1 minute or more.

  1. Enter the following menu: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0622
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


3.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - GENERATOR - ECM)


    A191026E04
  1. Disconnect the A8 generator connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the generator connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    IG (A8-2) - Body ground
    11 to 14 V

  1. Turn the ignition switch OFF.

  1. Disconnect the E8 ECM connector.

  1. Measure the resistance of the harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    M (A8-3) - ALT (E8-8)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    M (A8-3) or ALT (E81-8) - Body ground
    10 kΩor higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT GENERATOR ASSEMBLY (GENERATOR ROTOR)


    B012264E01
  1. Remove the generator assembly (Click here).

  1. Remove the generator rotor assembly (Click here).

  1. Measure the resistance between the slip rings of generator rotor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Generator slip rings
    20°C(68°F)
    1.85 to 2.25 Ω



    B012265E01
  1. Measure the resistance between the slip ring and generator rotor assembly.

Standard resistance:
Tester Connection
Specified Condition
Generator slip ring - Generator rotor
10 kΩ or higher



    A075676
  1. Inspect the slip rings of the generator rotor.

    1. Check that the slip rings are not rough or scored.

    2. Measure the slip ring diameter.

      Standard diameter:
      14.2 to 14.4 mm (0.559 to 0.567 in.)

      Minimum diameter:
      14.0 mm (0.551 in.)



NG
Go to step 6
OK


5.REPLACE GENERATOR ASSEMBLY
  1. Replace the generator assembly (Click here).



NEXT
Go to step 7

6.REPLACE GENERATOR ROTOR ASSEMBLY
  1. Replace the generator rotor assembly (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0622)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menu: Powertrain / Engine / DTC / Clear.

  1. Clear DTCs.

  1. Start the engine.

  1. Allow the engine to idle for 1 minute or more.

  1. Enter the following menu: Powertrain / Engine / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0622
    A
    No output
    B



B
END
A

REPLACE ECM (Click here)