Home › ENGINE ยท 5L-E › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation.



2. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the washer nozzle hose.

  1. Remove the 4 bolts and hood.



3. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 8 bolts and under cover.



4. REMOVE NO. 2 ENGINE UNDER COVER
  1. Remove the 4 bolts and under cover.



5. LOOSEN FUEL TANK CAP ASSEMBLY


6. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A114241
  1. Remove the reservoir cap and, using a wrench, remove the vent plug.



  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A114242E01



7. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug, and drain the oil into a container.

  1. Clean the drain plug, and install it and a new gasket.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



8. REMOVE BATTERY BRACKET
  1. Remove the bolt and battery bracket.



9. REMOVE BATTERY AND BATTERY TRAY


10. REMOVE AIR CLEANER ASSEMBLY
  1. Disconnect the IAT sensor connector.

  1. Loosen the air cleaner hose clamp.

  1. Remove the 2 bolts and air cleaner.



11. DISCONNECT RADIATOR HOSE INLET


12. DISCONNECT RADIATOR HOSE OUTLET


13. REMOVE VANE PUMP V BELT


    A121092E01
  1. Loosen bolt A and nut B, and remove the V belt.



14. REMOVE COOLER COMPRESSOR V BELT (w/ Air Conditioning System)


    A121093E01
  1. Loosen nut A and bolt B, and remove the V belt.



15. REMOVE FAN & GENERATOR V BELT (w/o Air Conditioning System)


    A142830E01
  1. Loosen the bolts A and B, and remove the V belt.



16. REMOVE FAN & GENERATOR V BELT (w/ Air Conditioning System)


    A115632E01
  1. Loosen the bolts A and B.

  1. Loosen adjusting bolt C, and remove the V belt.



17. REMOVE FAN SHROUD


    A114244
  1. Remove the 3 bolts and oil reservoir.

  1. Disconnect the No. 1 and No. 2 water by-pass hoses from the tank upper and lower.

  1. Remove the bolt and radiator reservoir.

  1. Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the vane pump V belt, cooler compressor V belt and fan and generator V belt (Click here).

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.



18. REMOVE RADIATOR ASSEMBLY


A097639E01
  1. Remove the 4 bolts and radiator.



19. REMOVE STARTER ASSEMBLY


    A118417
  1. Disconnect the starter connector.

  1. Remove the terminal cap.

  1. Remove the nut, and disconnect the terminal 30 wire.



    A118418
  1. Remove the nut, 2 bolts and stay.

  1. Remove the nut, 2 bolts and starter.



20. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Remove the 3 bolts and heat insulator.



21. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts from the transmission.

  1. Remove the 5 clips and front fender seal LH.

  1. Remove the 3 nuts from the exhaust manifold.

  1. Disconnect the front exhaust pipe from the exhaust manifold and remove the gasket.

  1. Remove the bolt, clamp and pipe support from the front exhaust pipe.



22. REMOVE PROPELLER SHAFT ASSEMBLY
  1. for Front Side:
    Remove the propeller shaft (Click here).

  1. for Rear Side:
    Remove the propeller shaft (Click here).



23. REMOVE TRANSMISSION ASSEMBLY


C112945E04
  1. Using a transmission jack, support the transmission.

  1. Remove the support stand from the rear side.

  1. Remove the 4 bolts and transmission.



24. REMOVE CLUTCH COVER ASSEMBLY


D029616E03
  1. Place matchmarks on the clutch cover and flywheel.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 6 set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.



25. REMOVE CLUTCH DISC ASSEMBLY

NOTICE:
Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.



26. REMOVE FLYWHEEL SUB-ASSEMBLY


A058716E01
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. Remove the 8 bolts and flywheel.



27. REMOVE REAR END PLATE
  1. Remove the 2 bolts and rear end plate.



28. DISCONNECT HOSES AND CONNECTORS


    G035294E01
  1. Remove the engine room relay block cover (upper).

  1. Remove the engine room relay block cover (side).

  1. Remove the nut and disconnect the engine room junction block wire.

  1. Disconnect the 2 engine room junction block connectors.

  1. Remove the bolt and disconnect the ground cable.



    A121131
  1. Disconnect the 2 fuel hoses.



    A121130
  1. Disconnect the 2 water hoses.

  1. Remove the water hose clamp bolt.



    A121846
  1. Disconnect the compressor connector.



    A142763
  1. Disconnect the connectors as shown in the illustration.

  1. Disconnect the vacuum pump hose from the generator.



29. DISCONNECT COMPRESSOR AND MAGNET CLUTCH (w/ Air Conditioning System)


    A123646
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.



30. DISCONNECT VANE PUMP ASSEMBLY


    A071326E01
  1. Using SST, stop the pulley rotation and loosen the nut.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the nut and vane pump pulley from the vane pump shaft.

  1. Remove the 2 bolts and nut, and disconnect the vane pump.

    HINT:
    Disconnect the vane pump with the hoses connected, and it should be hung with a rope.



31. INSTALL NO. 2 ENGINE HANGER


    A058743E02
  1. Set the No. 2 engine hanger to the location shown in the illustration.

    Torque:
    37 N*m{ 380 kgf*cm , 27 ft.*lbf }

    Engine hanger part No.: 
    Part Name
    Part No.
    No. 2 engine hanger
    12282-54050
    Bolt
    91622-61022

    NOTICE:
    Install the engine hanger with new bolt.



32. REMOVE ENGINE ASSEMBLY
  1. Hold the engine with an engine sling device and chain block.

  1. Remove the 4 bolts and 4 nuts.

  1. Remove the engine by operating the engine sling device and chain block.



33. INSTALL ENGINE ON ENGINE STAND


34. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine assembly.



35. REMOVE FAN BELT ADJUSTING BAR (w/o Air Conditioning System)


    A142831
  1. Remove the 3 bolts and fan belt adjusting bar.



36. REMOVE COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)


    A112016E01
  1. Remove the bolt and spacer.



    A121135E01
  1. Remove the 4 bolts and compressor mounting bracket.



37. REMOVE GENERATOR ASSEMBLY


A118424
  1. Detach the terminal cap.

  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.



    A118425
  1. Remove the union bolt to disconnect the vacuum pump hose and remove the 2 gaskets.

  1. Remove the union bolt to disconnect the vacuum pump oil inlet hose and remove the 2 gaskets.

  1. Detach the vacuum pump oil inlet hose from the cord clip.

  1. Disconnect the vacuum pump oil outlet hose.



    A122287
  1. Remove the bolt and generator.



38. REMOVE INTAKE PIPE


    A123770
  1. Loosen the intake pipe clamp.

  1. Remove the 2 bolts and intake pipe.



39. REMOVE OIL DIPSTICK SUB-ASSEMBLY


40. REMOVE OIL DIPSTICK GUIDE
  1. Remove the 2 bolts, guide and O-ring.



41. REMOVE VENTURI ASSEMBLY


    A111052E02
  1. Disconnect the throttle open switch connector.



    A111053E02
  1. Disconnect the throttle control motor connector.

  1. Remove the venturi and gasket.



42. REMOVE INJECTION PIPE SET


    A121940
  1. Using a union nut wrench, loosen the 8 union nuts of the 4 injection pipes.

  1. Remove the 2 nuts, 2 upper pipe clamps and 4 injection pipes together with the lower pipe clamps.



43. REMOVE NO. 1 GLOW PLUG CONNECTOR
  1. Remove the nut and disconnect the glow plug connector wire.

  1. Remove the 4 screw grommets, 4 nuts and glow plug connector.



44. REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY


    A121941
  1. Disconnect the fuel hose from the leakage pipe.

  1. Remove the 4 nuts, leakage pipe and 4 ring packing washers.



45. REMOVE NOZZLE HOLDER & NOZZLE SET


    A121942E01
  1. Using SST, remove the 4 injection nozzles, 4 injection nozzle seats and 4 injection nozzle seat gaskets.

    SST
    09268-64010   (09268-64020)



46. REMOVE GLOW PLUG ASSEMBLY


    A139524
  1. Using a 12 mm deep socket wrench, remove the 4 glow plugs.



47. REMOVE INJECTION PUMP DRIVE PULLEY


    A071313E01
  1. Using SST, remove the pulley nut.

    SST
    09213-14010   (91651-60865)
    09330-00021  



    A071314E01
  1. Using SST, remove the drive pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)



48. REMOVE INJECTION PUMP ASSEMBLY


    A121086E01
  1. Disconnect the engine speed sensor connector.

  1. Disconnect the spill control valve connector.

  1. Disconnect the correction unit connector.

  1. Disconnect the timing control valve connector.

  1. Disconnect the fuel temperature sensor connector.

  1. Disconnect the engine wire clamp.

  1. Disconnect the 3 fuel hoses.



    A071318E01
  1. Remove the 3 bolts and injection pump stay.

  1. Remove the 2 nuts and injection pump.



49. REMOVE CRANKSHAFT POSITION SENSOR


    A114266
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.



50. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


    A111055E02
  1. Disconnect the sensor connector.

  1. Remove the sensor and gasket.



51. REMOVE WATER OUTLET HOUSING


    A113081
  1. Remove the 3 bolts, outlet housing and gasket.



52. REMOVE INTAKE MANIFOLD


    A113083
  1. Remove the 6 bolts, 2 nuts, intake manifold and gasket.



53. REMOVE WATER BY-PASS HOSE UNION
  1. Remove the water by-pass hose union.



54. REMOVE PUMP BRACKET


    A112057
  1. Remove the 6 bolts and pump bracket.



55. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET RH


    A121139
  1. Remove the 4 bolts and engine mounting bracket.



56. REMOVE EXHAUST MANIFOLD


    A121142
  1. Remove the 6 bolts, 2 nuts and manifold.

  1. Remove the manifold gasket from the cylinder head.



57. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY


    A112063
  1. Using a 24 mm deep socket wrench, remove the oil pressure switch.



58. REMOVE WIRE HARNESS CLAMP BRACKET
  1. Remove the bolt and wire harness clamp bracket.