Home › BODY › INSTRUMENT PANEL › UPPER INSTRUMENT PANEL

UPPER INSTRUMENT PANEL > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL GLOVE COMPARTMENT DOOR LOCK ASSEMBLY
  1. Install the glove compartment door lock with the 2 screws.



2. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY


  1. for LHD:

    1. Attach the 5 guides and 8 claws to install the upper instrument panel.



    2. Install the 2 bolts <A> and 2 screws <B>.


      B278740E01


      Text in Illustration 
      *1
      Bolt <A>
      *2
      Screw <B>



  1. for RHD:

    1. Attach the 5 guides and 8 claws to install the upper instrument panel.



    2. Install the 2 bolts <A> and 2 screws <B>.


      B278741E01


      Text in Illustration 
      *1
      Bolt <A>
      *2
      Screw <B>



3. INSTALL FRONT PILLAR GARNISH LH
  1. w/ Curtain Shield Airbag:

    1. Remove the protective cover.

  1. Attach the 2 guides and 2 clips to install the front pillar garnish.

  1. Install the front door opening trim.



4. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.



5. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY

HINT:
Use the same procedure for both assist grip.

  1. Install the assist grip with the 2 screws.



6. INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH

HINT:
Use the same procedure for both front No. 1 assist grip plugs.

  1. Attach the 2 claws to install the front No. 1 assist grip plug.



7. INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH

HINT:
Use the same procedure described for the LH side.



8. INSTALL INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY


C126904
  1. Attach the 12 claws to install the airbag.

  1. Attach the clamp to the bracket.



    C126903
  1. Install the 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    C126902
  1. Connect the connector to the airbag.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.



9. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


B278068E01
  1. Attach the 2 hinges to install the glove compartment door.
    Text in Illustration 
    *1
    Hinge



    B278069E01
  1. While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.
    Text in Illustration 
    *1
    Stopper



10. INSTALL RADIO TUNER OPENING COVER (w/o Audio)
  1. Install the radio tuner opening cover with the 4 screws.



11. INSTALL RADIO RECEIVER ASSEMBLY (w/ Audio)
  1. for Radio Receiver Type:

  1. for Radio and Display Type:



12. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
  1. for Manual Air Conditioning System:

    1. Connect the connectors.

    2. Attach the 4 claws to connect the air conditioner control.

    3. Attach the 10 claws and 4 clips to install the center instrument cluster finish panel.

  1. for Automatic Air Conditioning System:

    1. Connect the connectors.

    2. Attach the 8 claws and 4 clips to install the center instrument cluster finish panel.



13. INSTALL COMBINATION METER ASSEMBLY
  1. Connect the connectors and attach the clamp.

  1. Install the combination meter with the 3 screws.



14. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL
  1. Attach the 2 claws and 3 guides to install the No. 1 instrument cluster finish panel.

  1. Install the clip <C>.



15. INSTALL STEERING WHEEL ASSEMBLY
(Click here)


16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



17. CHECK SRS WARNING LIGHT
(Click here)