DTC C1405 Open or Short in Front Speed Sensor RH Circuit |
DTC C1406 Open or Short in Front Speed Sensor LH Circuit |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1405 C1406 | Either condition is met:
|
|

| 1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Speed Open | Front speed sensor RH open circuit detection / Error or Normal | Normal | - |
| FL Speed Open | Front speed sensor LH open circuit detection / Error or Normal | Normal | - |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Wheel Speed | Front speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| FL Wheel Speed | Front speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
Check the speed value output from the speed sensor displayed on the intelligent tester.
|
| ||||
| OK | |
| 3.RECONFIRM DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S25-7 (FR+) - S5-1 (FR+) | Always | Below 1 Ω |
| S25-7 (FR+) - Body ground | Always | 10 kΩ or higher |
| S25-6 (FR-) - S5-2 (FR-) | Always | Below 1 Ω |
| S25-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| S25-19 (FL+) - S4-1 (FL+) | Always | Below 1 Ω |
| S25-19 (FL+) - Body ground | Always | 10 kΩ or higher |
| S25-18 (FL-) - S4-2 (FL-) | Always | Below 1 Ω |
| S25-18 (FL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK TERMINAL VOLTAGE (FR+, FL+ TERMINAL) |
Turn the ignition switch off.
Connect the skid control ECU (brake actuator assembly) connector.
Disconnect the front speed sensor connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S5-1 (FR+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| S4-1 (FL+) - Body ground | Ignition switch ON | 8 to 14 V |
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector (to Front Speed Sensor) |
|
| ||||
| OK | ||
| ||