DTC B2799/99 Engine Immobiliser System Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
| B2799 | Either condition is met (1 trip detection logic*1):
|
| Either condition is met:
|
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
| Engine cannot be started. | - |
| DTC Code | Data List and Active Test |
| B2799 | - |

| 1.CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2.CHECK FOR DTC |
Check for the DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 3.REREGISTER ECU COMMUNICATION ID |
Reregister the ECU - ECM communication ID (Refer to Service Bulletin).
| NEXT | |
| 4.CLEAR DTC |
Clear the DTCs (Click here)
| NEXT | |
| 5.CHECK FOR DTC |
Check for the DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 6.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Check that the connectors are properly connected to the ECM and transponder key ECU assembly.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (SFI OR ECD COMMUNICATION LINE) |
Disconnect the T21 transponder key ECU assembly connector.
Disconnect the E5*1, E9*2 or E13*3 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) - E5-30 (IMI) | Always | Below 1 Ω |
| T21-12 (EFII) - E5-29 (IMO) | Always | Below 1 Ω |
| T21-13 (EFIO) or E5-30 (IMI) - Body ground | Always | 10 kΩ or higher |
| T21-12 (EFII) or E5-29 (IMO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) - E9-16 (IMI) | Always | Below 1 Ω |
| T21-12 (EFII) - E9-15 (IMO) | Always | Below 1 Ω |
| T21-13 (EFIO) or E9-16 (IMI) - Body ground | Always | 10 kΩ or higher |
| T21-12 (EFII) or E9-15 (IMO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) - E13-16 (IMI) | Always | Below 1 Ω |
| T21-12 (EFII) - E13-15 (IMO) | Always | Below 1 Ω |
| T21-13 (EFIO) or E13-16 (IMI) - Body ground | Always | 10 kΩ or higher |
| T21-12 (EFII) or E13-15 (IMO) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) or E5-30 (IMI) - Body ground | Always | Below 1 V |
| T21-12 (EFII) or E5-29 (IMO) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) or E9-16 (IMI) - Body ground | Always | Below 1 V |
| T21-12 (EFII) or E9-15 (IMO) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) or E13-16 (IMI) - Body ground | Always | Below 1 V |
| T21-12 (EFII) or E13-15 (IMO) - Body ground | Always | Below 1 V |
|
| ||||
| OK | |
| 8.REPLACE ECM |
Temporarily replace the ECM with a new one.
| NEXT | |
| 9.REREGISTER ECU COMMUNICATION ID |
Reregister the ECU - ECM communication ID (Refer to Service Bulletin).
| NEXT | |
| 10.CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 11.CHECK FOR DTC |
Check for the DTCs (Click here).
|
| ||||
| OK | ||
| ||