Home › TRANSMISSION ยท A340F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


B277221
  1. Twist the shift lever knob in the direction indicated by the arrow and remove it.



3. REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY


B278222
  1. Detach the 4 claws and remove the parking brake hole cover.



4. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


  1. for Manual Transmission:



    1. Detach the 12 claws and remove the upper console panel.

      NOTICE:
      Be careful not to damage the instrument panel and console box with the claws of the upper console panel.



      B277219E01


      Text in Illustration 
      *A
      for 2WD
      *B
      for 4WD



  1. for Automatic Transmission:



    1. Detach the 12 claws and remove the upper console panel.

      NOTICE:
      Be careful not to damage the instrument panel and console box with the claws of the upper console panel.



      B277220E01


      Text in Illustration 
      *A
      for 2WD
      *B
      for 4WD



5. REMOVE CONSOLE BOX ASSEMBLY


B278048E01
  1. Remove the 4 screws and 2 bolts.

  1. Using a clip remover, remove the 2 clips and console box.
    Text in Illustration 
    *1
    Screw
    *2
    Bolt
    *3
    Clip



6. REMOVE SHIFT LEVER BOOT ASSEMBLY
  1. Remove the 4 screws and shift lever boot.



7. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY


    C234783
  1. Using needle-nose pliers, remove the snap ring and pull out the shift lever from the shift lever retainer.

    HINT:
    Move the transfer shift lever to the H4 position.



8. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 4 bolts and No. 1 engine under cover.



9. REMOVE NO. 2 ENGINE UNDER COVER
  1. Remove the 2 bolts and No. 2 engine under cover.



10. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the front pipe from the outlet pipe and remove the gasket.

  1. Remove the front pipe from the pipe support.



11. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


12. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
(Click here)


13. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }



14. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


G039346E01
  1. Remove the oil dipstick.

  1. Remove the 2 bolts and oil filler tube.

  1. Remove the O-ring from the oil filler tube.



15. DISCONNECT OIL COOLER TUBE


G034850
  1. Using a 17 mm union nut wrench, disconnect the outlet tube and inlet tube.



    G034255E01
  1. Remove the 3 bolts and 3 clamps.



16. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


G034515E01
  1. Remove the nut and disconnect the control cable.

  1. Remove the clip and disconnect the control cable.



17. REMOVE TRANSMISSION CONTROL CABLE BRACKET


G034516E01
  1. Remove the 2 bolts and control cable bracket from the transmission.



18. REMOVE STARTER ASSEMBLY


A111843
  1. Disconnect the starter connector.

  1. Open the terminal cap.

  1. Remove the nut and disconnect the starter wire.



    A122908
  1. Remove the 2 nuts, bolt, ground cable and starter.



19. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


G034518E01
  1. Support the transmission with a transmission jack.



20. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


G034256
  1. Remove the 4 set bolts of the No. 1 engine mounting insulator rear.

  1. Remove the 4 nuts, 4 bolts and frame crossmember.



21. DISCONNECT CONNECTOR


G034519E01
  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.

  1. Transmission side:
    Disconnect the connectors.

    1. Disconnect the temperature sensor connector.

    2. Disconnect the park/neutral position switch connector.

    3. Disconnect the 2 speed sensor connectors.

    4. Disconnect the transmission wire connector.

  1. Transfer side:
    Disconnect the connectors.

    1. Disconnect the indicator switch connector (4WD).

    2. Disconnect the speedometer sensor connector.

    3. Disconnect the indicator switch connector (L4).

    4. Disconnect the indicator switch connector (neutral).



22. DISCONNECT WIRE HARNESS


23. REMOVE STIFFENER PLATE


G034607E03
  1. Remove the 4 bolts and stiffener plate RH (with clamp tube).

  1. Remove the 4 bolts and stiffener plate LH.

  1. Remove the No. 4 cylinder block insulator.

  1. Remove the No. 2 end plate.



24. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT


G034258E01
  1. Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley bolt with a wrench and remove the 6 drive plate and torque converter setting bolts.



25. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


    G034259E01
  1. Remove the 5 bolts.

  1. Separate the transmission from the engine.

    NOTICE:
    Do not pry between the transaxle assembly and engine more than necessary to prevent the knock pins from being damaged.



26. REMOVE NO. 1 ENGINE MOUNTING INSULATOR REAR


G034260E01
  1. Remove the 4 bolts and engine mounting insulator.



27. REMOVE TRANSFER ASSEMBLY
(Click here)


28. REMOVE TORQUE CONVERTER ASSEMBLY