Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (for RHD)

POWER WINDOW CONTROL SYSTEM (for RHD) > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

If the front passenger side manual UP / DOWN function does not operate, a malfunction may be present in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.

WIRING DIAGRAM


B149731E04


INSPECTION PROCEDURE

1.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (POWER SOURCE)
B149730E07
  1. Disconnect the P11 regulator switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    P11-3 - Body ground
    Ignition switch ON
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
B063163E03
  1. Remove the switch (Click here).

  1. Measure the resistance of the switch when the switch is operated.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 - 4, 2 - 3
    UP
    Below 1 Ω
    5 - 4, 2 - 1
    OFF
    Below 1 Ω
    5 - 3, 2 - 1
    DOWN
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY
OK


3.CHECK WIRE HARNESS (REGULATOR SWITCH - REGULATOR MOTOR)

B149732E03

  1. Disconnect the P11 switch connector.

  1. Disconnect the P7 motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    P11-5 - P7-1
    Below 1 Ω
    P11-2 - P7-2
    Below 1 Ω
    P11-5 or P7-1 - Body ground
    10 kΩ or higher
    P11-2 or P7-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY
B086401E01
  1. Remove the motor (Click here).

  1. Apply battery voltage to connector terminals 1 and 2.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY
OK


5.CHECK WIRE HARNESS (MASTER SWITCH - REGULATOR SWITCH)

B149733E05

  1. Disconnect the P6 master switch connector.

  1. Disconnect the P11 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    P6-10 (PU) - P11-1
    Below 1 Ω
    P6-13 (PD) - P11-4
    Below 1 Ω
    P6-10 (PU) or P11-1 - Body ground
    10 kΩ or higher
    P6-13 (PD) or P11-4 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Front Passenger Switch)


    B085831E02
  1. Remove the master switch (Click here).

  1. Measure the resistance of the switch when the switch is operated.

    Standard resistance:

    Tester Connection
    Window Lock Switch Condition
    Front Passenger Switch Condition
    Specified Condition
    3 (E) - 13 (PD), 6 (B) - 10 (PU)
    OFF
    UP
    Below 1 Ω
    3 (E) - 10 (PU), 3 (E) - 13 (PD)
    OFF
    OFF
    Below 1 Ω
    3 (E) - 10 (PU), 6 (B) - 13 (PD)
    OFF
    DOWN
    Below 1 Ω
    3 (E) - 13 (PD)
    ON
    UP
    10 kΩ or higher
    6 (B) - 10 (PU)
    Below 1 Ω
    13 (PD) - 10 (PU)
    ON
    OFF
    Below 1 Ω
    3 (E) - 10 (PU)
    ON
    DOWN
    10 kΩ or higher
    6 (B) - 13 (PD)
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL