Home › TRANSMISSION ยท G58F MANUAL TRANSMISSION › MANUAL TRANSMISSION ASSEMBLY

MANUAL TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TRANSFER ASSEMBLY
  1. Install the transfer to the transmission.

  1. Install the 2 clamps and 8 bolts.

    Torque:
    24 N*m{ 244 kgf*cm , 17 ft.*lbf }



2. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY


C112945E02
  1. Align the input shaft with the clutch disc and install the transmission to the engine.

  1. Install the 4 bolts.

    Torque:
    72 N*m{ 730 kgf*cm , 53 ft.*lbf }



3. INSTALL STIFFENER PLATE


C121621E10
  1. Install the stiffener plate RH with the 4 bolts.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf } for bolt A
    37 N*m{ 377 kgf*cm , 27 ft.*lbf } for bolt B

  1. Install the stiffener plate LH with the 4 bolts.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf } for bolt A
    37 N*m{ 377 kgf*cm , 27 ft.*lbf } for bolt B



4. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR


G034226E05
  1. Install the mounting insulator with the 4 bolts.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



5. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


B085193E16
  1. Install the frame crossmember with the 4 bolts and 4 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf } for bolt A

  1. Install the 4 set bolts to the rear No. 1 engine mounting insulator.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf } for bolt B



6. INSTALL STARTER ASSEMBLY
(Click here)


7. CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY


G034223E01
  1. Connect the release cylinder with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



8. CONNECT WIRE HARNESS
  1. Transmission side:
    Connect the back-up light switch connector.

  1. Transfer side:
    Connect the No. 1, No. 2 and No. 3 transfer indicator switch connectors, and vehicle speed sensor connector.



9. INSTALL FRONT EXHAUST PIPE ASSEMBLY
(Click here)


10. INSTALL REAR PROPELLER SHAFT ASSEMBLY
(Click here)


11. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


12. ADD MANUAL TRANSMISSION OIL


D025304E26

Oil grade:
GL-4

Viscosity:
SAE 75W-90

Standard capacity:
2.2 liters (2.3 US qts, 1.9 Imp. qts)

Torque:
37 N*m{ 377 kgf*cm , 27 ft.*lbf }



13. ADD TRANSFER OIL
  1. Remove the case plug (for filler) and gasket.

  1. Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.20 in.) from the bottom lip of the case plug (for filler) hole.

    NOTICE:
    1. When adding oil, pour it slowly.
    2. Add oil a little at a time, waiting several minutes between each addition of oil.

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new gasket and the case plug (for filler).

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



14. INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }



15. INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }



16. INSTALL TRANSFER CASE LOWER PROTECTOR
  1. Install the transfer case lower protector with the 4 bolts.

    Torque:
    18 N*m{ 183 kgf*cm , 13 ft.*lbf }



17. INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY
  1. Install the transfer shift lever.

    HINT:
    Apply MP grease to the tip of the transfer shift lever.

  1. Using pliers, install the snap ring.



18. INSTALL FLOOR SHIFT LEVER ASSEMBLY
  1. Cover the shift lever cap with a cloth.

  1. Press down on the shift lever cap and rotate it clockwise to install it.

    HINT:
    Apply MP grease to the tip of the shift lever.



19. INSTALL SHIFT LEVER BOOT ASSEMBLY


G034544E03
  1. Install the shift lever boot with the 4 screws and 2 clips.



20. INSTALL CONSOLE BOX ASSEMBLY
(Click here)


21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).