DTC P0087 Fuel Rail / System Pressure - Too Low |
DTC P0190 Fuel Rail Pressure Sensor Circuit |
DTC P0192 Fuel Rail Pressure Sensor Circuit Low Input |
DTC P0193 Fuel Rail Pressure Sensor Circuit High Input |

| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds | Fuel pressure sensor output voltage stays at fixed value for 90 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 1 second | Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or higher for 0.5 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 1 second | Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 1 second | Fuel pressure sensor output voltage is 4.9 V or higher for 0.5 seconds (1 trip detection logic). |
|
| DTC No. | Data List |
| P0087 |
|
| P0190 | |
| P0192 | |
| P0193 |


| 1.CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0190, P0192 or P0193 is output | A |
| P0087 is output | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM) |
Disconnect the fuel pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F32-5 (PR) - E7-26 (PCR1) | Always | Below 1 Ω |
| F32-2 (PR2) - E7-33 (PCR2) | Always | Below 1 Ω |
| F32-1 (VCS) - E6-2 (VCS) | Always | Below 1 Ω |
| F32-6 (VC) - E7-18 (VC) | Always | Below 1 Ω |
| F32-4 (E2) - E7-28 (E2) | Always | Below 1 Ω |
| F32-3 (E2S) - E6-1 (E2S) | Always | Below 1 Ω |
| F32-5 (PR) or E7-26 (PCR1) - Body ground | Always | 10 kΩ or higher |
| F32-2 (PR2) or E7-33 (PCR2) - Body ground | Always | 10 kΩ or higher |
| F32-1 (VCS) or E6-2 (VCS) - Body ground | Always | 10 kΩ or higher |
| F32-6 (VC) or E7-18 (VC) - Body ground | Always | 10 kΩ or higher |
| F32-4 (E2) or E7-28 (E2) - Body ground | Always | 10 kΩ or higher |
| F32-3 (E2S) or E6-1 (E2S) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel pressure sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE) |
![]() |
Disconnect the fuel pressure sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F32-6 (VC) - F32-4 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| F32-1 (VCS) - F32-3 (E2S) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Fuel Pressure Sensor) |
Reconnect the fuel pressure sensor connector.
|
| ||||
| OK | |
| 4.REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR) |
Replace the common rail assembly (Click here).
| NEXT | |
| 5.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0190, P0192 OR P0193) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (Click here).
Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0087, P0190, P0192 or P0193 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 7.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 8.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.
Confirm that the DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P0087, P0190, P0192 and/or P0193.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, increase the idling time.
| NEXT | ||
| ||