Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0627    Fuel Pump Control Circuit / Open

for Preparation Click here


DESCRIPTION


P0627 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 1 second
Even though the CPU (command area inside the ECU) is outputting the suction control valve operation duty, the output monitor signal is absent for 0.5 seconds (1 trip detection logic).
  1. Open or short in suction control valve circuit
  2. Suction control valve (fuel supply pump assembly)
  3. ECM

Related Data List 
DTC No.
Data List
P0627
Fuel Press
Target Common Rail Pressure

HINT:
  1. For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (Click here).
  2. When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Fuel Press.
    Under a stable operating condition such as idling, Fuel Press is within 5000 kPa of Target Common Rail Pressure.


WIRING DIAGRAM

Refer to DTC P0088 .

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.INSPECT FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
  1. Inspect the fuel supply pump assembly (Click here).



NG
Go to step 4
OK


2.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
  1. Disconnect the suction control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    S8-1 - E7-2 (PCV+)
    Always
    Below 1 Ω
    S8-2 - E7-1 (PCV-)
    Always
    Below 1 Ω
    S8-1 or E7-2 (PCV+) - Body ground
    Always
    10 kΩ or higher
    S8-2 or E7-1 (PCV-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the suction control valve connector.

  1. Reconnect the ECM connector.



NG
Go to step 8
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0627)
  1. Connect the intelligent tester to the DLC3

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and idle it for 1 second or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0627 is output
    B



B
Go to step 7
A

END 

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
  1. Replace the fuel supply pump assembly (Click here).


NEXT


5.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


6.PERFORM FUEL SUPPLY PUMP INITIALIZATION
  1. Perform fuel supply pump initialization (Click here).



NEXT
Go to step 9

7.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 9

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine and idle it for 1 second or more.

  1. Confirm that the DTC is not output again.


NEXT

END