DTC P1229 Fuel Pump System |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Idling for 60 seconds | The actual fuel pressure exceeds the target fuel pressure by 5000 kPa or higher for 30 seconds. (1 trip detection logic) |
|
| DTC No. | Data List |
| P1229 |
|
| 1.CHECK OTHER DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P1229 and "P0190, P0192 and/or P0193" are output | B |
| Except above | A |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND TARGET COMMON RAIL PRESSURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.
Check that the internal fuel pressure of the common rail is within the specification below.
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM) |
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S8-1 - E7-2 (PCV+) | Always | Below 1 Ω |
| S8-2 - E7-1 (PCV-) | Always | Below 1 Ω |
| S8-1 or E7-2 (PCV+) - Body ground | Always | 10 kΩ or higher |
| S8-2 or E7-1 (PCV-) - Body ground | Always | 10 kΩ or higher |
Reconnect the suction control valve connector.
Reconnect the ECM connector.
|
| ||||
|
| ||||
| 4.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.
![]() |
Take a snapshot with the intelligent tester during the Active Test.
| *1 | Snapshot Button |
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed (Click here).

| Result | Proceed to |
| The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa. | B |
| Except above | A |
|
| ||||
| A | |
| 6.REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY |
Replace the fuel filter element sub-assembly (Click here).
| NEXT | |
| 7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE) |
Replace the fuel supply pump assembly (Click here).
| NEXT | |
| 8.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 9.PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
| NEXT | |
| 10.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
Idle the engine for 60 seconds, and then run it at 2500 rpm without load for 60 seconds.
Confirm that the DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P1229.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, increase the idling time.
| NEXT | ||
| ||