Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Auto Up / Down Function does not Operate

for Preparation Click here


DESCRIPTION

If the auto up/down function does not operate, the cause may be one or more of the following:
  1. The recorded power window fully closed position, which is stored in the power window regulator master switch assembly, was erased as a result of: 1) the PWR H-fuse or DOOR fuse being replaced; or 2) the battery cable and the master switch's connector being disconnected.
  2. The power window regulator master switch assembly has a malfunction.
  3. The pulse sensors in the front door window regulator sub-assembly (for driver side) have a malfunction.
  4. The wiring between the power window regulator master switch assembly and the front door window regulator sub-assembly (for driver side) is open or short-circuited.

WIRING DIAGRAM


B280492E05


INSPECTION PROCEDURE

1.CHECK MANUAL UP/DOWN FUNCTION (FOR DRIVER SIDE)
  1. Check that the manual up/down function operates normally.

    OK:
    Manual up/down function operates normally.



NG
GO TO DRIVER SIDE POWER WINDOW MANUAL FUNCTION DOES NOT OPERATE WITH POWER WINDOW MASTER SWITCH (Click here)
OK


2.CHECK LIGHT OF POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


  1. Turn the ignition switch to ON.


    B277627E03


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *1
    AUTO Light
    -
    -

  1. Operate the master switch's driver side power window switch for 2 seconds or more.



  1. Check the blinking pattern of the AUTO light. Compare the blinking pattern with the illustration.


    B278579E01

    Result 
    Blinking Pattern
    Proceed to
    1 or 3
    A
    2
    B
    4
    C



B
Go to step 4

C
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
A


3.RESET FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (FOR DRIVER SIDE)
  1. Check that the power window operates normally after reset (Click here).

    OK:
    Power window operates normally.



NG
Go to step 4
OK

END 

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY [FOR DRIVER SIDE])
  1. Disconnect the P6 power window regulator master switch assembly connector.

  1. Disconnect the P7*1 or P8*2 front door window regulator sub-assembly (for driver side) connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    P6-3 (VCC) - P7-4
    Always
    Below 1 Ω
    P6-14 (PLS) - P7-5
    Always
    Below 1 Ω
    P6-17 (PLS2) - P7-3
    Always
    Below 1 Ω
    P6-2 (GND) - P7-6
    Always
    Below 1 Ω
    P6-3 (VCC) or P7-4 - Body ground
    Always
    10 kΩ or higher
    P6-14 (PLS) or P7-5 - Body ground
    Always
    10 kΩ or higher
    P6-17 (PLS2) or P7-3 - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    P6-3 (VCC) - P8-4
    Always
    Below 1 Ω
    P6-14 (PLS) - P8-5
    Always
    Below 1 Ω
    P6-17 (PLS2) - P8-3
    Always
    Below 1 Ω
    P6-2 (GND) - P8-6
    Always
    Below 1 Ω
    P6-3 (VCC) or P8-4 - Body ground
    Always
    10 kΩ or higher
    P6-14 (PLS) or P8-5 - Body ground
    Always
    10 kΩ or higher
    P6-17 (PLS2) or P8-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (PLS, PLS2 SIGNAL)


    B276285E26
  1. Remove the power window regulator master switch assembly with its connectors still connected (Click here).

  1. Using an oscilloscope, check the waveform.

    OK:
    Tester Connection
    Switch Condition
    Specified Condition
    P6-14 (PLS) - Body ground
    Ignition switch ON, driver side power window switch off → up or down
    Pulse waveform is output
    P6-17 (PLS2) - Body ground

    Text in Illustration 
    *a
    Component with harness connected
    (Power Window Regulator Master Switch Assembly)



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK

REPLACE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (FOR DRIVER SIDE) (Click here)