POWER WINDOW CONTROL SYSTEM > Auto Up / Down Function does not Operate |

| 1.CHECK MANUAL UP/DOWN FUNCTION (FOR DRIVER SIDE) |
Check that the manual up/down function operates normally.
|
| ||||
| OK | |
| 2.CHECK LIGHT OF POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |
Turn the ignition switch to ON.

| *A | for LHD | *B | for RHD |
| *1 | AUTO Light | - | - |
Operate the master switch's driver side power window switch for 2 seconds or more.
Check the blinking pattern of the AUTO light. Compare the blinking pattern with the illustration.

| Blinking Pattern | Proceed to |
| 1 or 3 | A |
| 2 | B |
| 4 | C |
|
| ||||
|
| ||||
| A | |
| 3.RESET FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (FOR DRIVER SIDE) |
Check that the power window operates normally after reset (Click here).
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY [FOR DRIVER SIDE]) |
Disconnect the P6 power window regulator master switch assembly connector.
Disconnect the P7*1 or P8*2 front door window regulator sub-assembly (for driver side) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P6-3 (VCC) - P7-4 | Always | Below 1 Ω |
| P6-14 (PLS) - P7-5 | Always | Below 1 Ω |
| P6-17 (PLS2) - P7-3 | Always | Below 1 Ω |
| P6-2 (GND) - P7-6 | Always | Below 1 Ω |
| P6-3 (VCC) or P7-4 - Body ground | Always | 10 kΩ or higher |
| P6-14 (PLS) or P7-5 - Body ground | Always | 10 kΩ or higher |
| P6-17 (PLS2) or P7-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| P6-3 (VCC) - P8-4 | Always | Below 1 Ω |
| P6-14 (PLS) - P8-5 | Always | Below 1 Ω |
| P6-17 (PLS2) - P8-3 | Always | Below 1 Ω |
| P6-2 (GND) - P8-6 | Always | Below 1 Ω |
| P6-3 (VCC) or P8-4 - Body ground | Always | 10 kΩ or higher |
| P6-14 (PLS) or P8-5 - Body ground | Always | 10 kΩ or higher |
| P6-17 (PLS2) or P8-3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (PLS, PLS2 SIGNAL) |
![]() |
Remove the power window regulator master switch assembly with its connectors still connected (Click here).
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Specified Condition |
| P6-14 (PLS) - Body ground | Ignition switch ON, driver side power window switch off → up or down | Pulse waveform is output |
| P6-17 (PLS2) - Body ground |
| *a | Component with harness connected (Power Window Regulator Master Switch Assembly) |
|
| ||||
| OK | ||
| ||