VEHICLE STABILITY CONTROL SYSTEM > TRC OFF Indicator Light Remains ON |
| 1.CHECK TERMINAL VOLTAGE (EXI3 TERMINAL) |
![]() |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S25-28 (EXI3) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly]) |
| Result | Proceed to | |
| NG | w/ Rear Differential Lock | A |
| w/o Rear Differential Lock | B | |
| OK | C | |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (EXI3 TERMINAL CIRCUIT) |
Turn the ignition switch off.
Disconnect the rear differential lock position switch (No. 4 transfer indicator switch) connector.
Disconnect the rear differential lock ECU (4 wheel drive control ECU) connector.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the C28 combination meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S25-28 (EXI3) - T29-2 | Always | Below 1 Ω |
| S25-28 (EXI3) - C28-9 | Always | Below 1 Ω |
| S25-28 (EXI3) - F18-1 (RLP) | Always | Below 1 Ω |
| S25-28 (EXI3) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT REAR DIFFERENTIAL LOCK SYSTEM |
Inspect rear differential lock system (Click here).
|
| ||||
| OK | |
| 4.READ VALUE USING GTS (TRC/VSC OFF MODE) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
| TRC/VSC Off Mode | VSC OFF switch / Normal, Unknown, TRC OFF or VSC OFF | Normal: Normal mode TRC OFF: TRC off mode VSC OFF: VSC off mode | - |
Check that the mode display changes according to VSC OFF switch operation.
|
| ||||
| OK | |
| 5.INSPECT BRAKE ACTUATOR ASSEMBLY |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
Check the state of the TRC OFF indicator light.
| Result | Proceed to |
| TRC OFF indicator light turns off | A |
| TRC OFF indicator light does not turn off | B |
|
| ||||
| A | ||
| ||
| 6.INSPECT VSC OFF SWITCH |
Turn the ignition switch off.
Remove the VSC OFF switch (Click here).
Inspect the VSC OFF switch (Click here).
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH) |
Turn the ignition switch off.
Disconnect the VSC OFF switch connector.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S25-30 (CSW) - V5-3 | Always | Below 1 Ω |
| S25-30 (CSW) - Body ground | Always | 10 kΩ or higher |
| V5-4 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the C28 combination meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S25-23 (INFR) - C28-21 | Always | Below 1 Ω |
| S25-23 (INFR) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||