Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC Code
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Speakers
  2. Radio and display receiver assembly
  3. Harness or connector

WIRING DIAGRAM


C240170E19


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Disconnect the R25 and R26 radio and display receiver assembly connectors.

  1. Clear the DTC (Click here).

  1. Check if DTC B15C3 is output.

    OK:
    DTC B15C3 is not output.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


2.CHECK FOR DTC
  1. Reconnect the R26 radio and display receiver assembly connector.

  1. Clear the DTC (Click here).

  1. Check if DTC B15C3 is output.

    OK:
    DTC B15C3 is not output.



NG
Go to step 7
OK


3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - FRONT NO. 2 SPEAKER)
  1. Disconnect the R25 radio and display receiver assembly connector.

  1. Disconnect the T25*1 and/or T24*2 speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    R25-1 (FR+) - T25-4
    Always
    Below 1 Ω
    R25-5 (FR-) - T25-2
    R25-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    R25-5 (FR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    R25-2 (FL+) - T24-4
    Always
    Below 1 Ω
    R25-6 (FL-) - T24-2
    R25-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    R25-6 (FL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 1 SPEAKER)
  1. *1: for RH
  2. *2: for LH
  1. Disconnect the T25*1 and/or T24*2 speaker connector.

  1. Disconnect the S16*1 and/or S15*2 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    T25-3 - S16-1
    Always
    Below 1 Ω
    T25-1 - S16-2
    T25-3 - Body ground
    Always
    10 kΩ or higher
    T25-1 - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    T24-3 - S15-1
    Always
    Below 1 Ω
    T24-1 - S15-2
    T24-3 - Body ground
    Always
    10 kΩ or higher
    T24-1 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E178457
  1. Disconnect the S16*1 and/or S15*2 speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Temporarily replace the speaker with a new or normally functioning one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    1. Connect all the speaker connectors to the speakers.
    2. When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.

    Result 
    Result
    Proceed to
    Malfunction disappears
    A
    Malfunction does not disappear
    B



B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
A

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - REAR SPEAKER)
  1. Disconnect the R26 radio and display receiver assembly connector.

  1. Disconnect the S18*1 and/or S17*2 speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    R26-1 (RR+) - S18-1
    Always
    Below 1 Ω
    R26-3 (RR-) - S18-2
    R26-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    R26-3 (RR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    R26-2 (RL+) - S17-1
    Always
    Below 1 Ω
    R26-6 (RL-) - S17-2
    R26-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    R26-6 (RL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT REAR SPEAKER ASSEMBLY


    E178457
  1. Disconnect the S18*1 and/or S17*2 speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)