P0617 Starter Relay Circuit High
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
| DTC No. |
DTC Detection Conditions |
Trouble Areas |
| P0617 |
When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic)
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
If the engine will not crank, proceed to the problem symptoms table (Click here).
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
| 1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.
- OK:
Ignition Switch Positions
Starter Signal
ON
OFF
START
ON
- Result:
Result
Proceed to
OK
A
NG
B (M/T Model)
NG
C (A/T Model)
|
|
||||
|
|
||||
| C | |
| 2. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() ![]() |
Disconnect the N8 PNP switch connector.
Measure the resistance when the transmission gear selector lever is moved to each position.
- Standard resistance:
Gear Selector
Lever Position
Tester Connection
Specified Condition
Except P and N
4 - 5
10 kΩ or higher
P
2 - 5
10 kΩ or higher
R
N
D
2
L
Reconnect the PNP switch connector.
|
|
||||
| NG | |
| 3. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
| NEXT | |
| 4. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.
- OK:
Ignition Switch Positions
Starter Signal
ON
OFF
START
ON
|
|
||||
| NG | |
| 5. INSPECT IGNITION SWITCH ASSEMBLY |
![]() ![]() |
Disconnect the I6 ignition switch connector.
Measure the resistance of the ignition switch.
- Standard resistance:
Tester Connection
Ignition Switch Position
Specified Condition
AM2 (5) - ST2 (7)
OFF
10 kΩ or higher
AM2 (5) - ST2 (7)
START
Below 1 Ω
Reconnect the ignition switch connector.
|
|
||||
| NG | |
| 6. REPLACE IGNITION SWITCH ASSEMBLY |
| NEXT | |
| 7. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.
- OK:
Ignition Switch Positions
Starter Signal
ON
OFF
START
ON
|
|
||||
| NG | |
| 8. REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - STA TERMINAL OF ECM) |
| NEXT | |
| 9. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the tester ON.
Clear DTCs (Click here).
Drive the vehicle at more than 20 km/h (12.43 mph) for over 20 seconds.
Enter the following menus: Powertrain / Engine / DTC.
Read DTCs.
- Result:
Display (DTC Output)
Proceed to
P0617
A
No DTC
B
|
|
||||
| A | ||
| ||


