Home › ENGINE › 1KD-FTV ENGINE CONTROL SYSTEM › ECD SYSTEM (w/o EGR Cooler)
ECM Power Source Circuit
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
When the ignition switch is turned ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes a current to flow to the coil, closing the contacts of the MAIN relay and supplying power to terminal +B of the ECM. WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
If the ECM is replaced, the new ECM needs initialization (Click here ).
1. CHECK ECM (+B VOLTAGE)
Turn the ignition switch ON.
Measure the voltage of the ECM connectors.
Standard voltage:
Tester Connection
Specified Condition
E5-1 (+B) - E7-7 (E1)
9 to 14 V
OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN ON PROBLEM SYMPTOMS TABLE
NG
2. CHECK WIRE HARNESS (ECM - BODY GROUND)
Disconnect the E7 ECM connector.
Measure the resistance of the wire harness side connector.
Standard resistance:
Tester Connection
Specified Condition
E7-7 (E1) - Body ground
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK
3. CHECK ECM (IGSW VOLTAGE)
Turn the ignition switch ON.
Measure the voltage of the ECM connectors.
Standard voltage:
Tester Connection
Specified Condition
E5-9 (IGSW) - E7-7 (E1)
9 to 14 V
OK
NG
4. INSPECT FUSE (IGN FUSE)
Remove the IGN fuse from the instrument panel J/B.
Measure the resistance of the fuse.
Standard resistance:
Below 1 Ω
NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK
5. INSPECT IGNITION SWITCH ASSEMBLY
Disconnect the I6 ignition switch connector.
Measure the resistance of the ignition switch.
Standard resistance:
Tester Connection
Switch Condition
Specified Condition
5 (AM2) - 6 (IG2)
LOCK
10 kΩ or higher
5 (AM2) - 6 (IG2)
ON
Below 1 Ω
NG
REPLACE IGNITION SWITCH ASSEMBLY
OK
REPAIR OR REPLACE HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION
SWITCH - ECM)
6. CHECK ECM (MREL VOLTAGE)
Turn the ignition switch ON.
Measure the voltage of the ECM connectors.
Standard voltage:
Tester Connection
Specified Condition
E5-8 (MREL) - E7-7 (E1)
9 to 14 V
NG
OK
7. INSPECT FUSE (EFI FUSE)
Remove the EFI fuse from the engine room junction block.
Measure the resistance of the fuse.
Standard resistance:
Below 1 Ω
NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK
8. INSPECT NO.1 INTEGRATION RELAY (MAIN RELAY)
Remove the No. 1 integration relay from the engine room junction block (Click here ).
Disconnect the 1J No. 1 integration relay connector.
Measure the voltage of the MAIN relay.
Standard voltage:
Tester Connection
Condition
Specified Condition
1J-4 - Body ground
Ignition switch ON
10 to 14 V
NG
REPLACE NO.1 INTEGRATION RELAY
OK
9. CHECK WIRE HARNESS (NO. 1 INTEGRATION RELAY (MAIN RELAY) - ECM)
Disconnect the 1J No. 1 integration relay connector from the engine room J/B (Click here ).
Disconnect the E5 ECM connector.
Measure the resistance of the wire harness side connectors.
Standard resistance:
Tester Connection
Specified Condition
1J-4 - E5-1 (+B)
Below 1 Ω
1J-4 or E5-1 (+B) - Body ground
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (MAIN RELAY) - ECM)
OK
REPAIR OR REPLACE HARNESS AND CONNECTOR (+B TERMINAL OF ECM - BATTERY POSITIVE TERMINAL)