DESCRIPTION
When the A/C compressor is on, the A/C amplifier sends the A/C signal to the ECM, then the ECM increases the fuel injection volume to improve driveability during engine idling.WIRING DIAGRAM


INSPECTION PROCEDURE
When using intelligent tester:
| 1. READ VALUE USING INTELLIGENT TESTER (AIR CONDITIONING SIGNAL) |
 |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the A/C switch ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / A/C SIG.
- Result:
A/C Compressor
|
Display
|
OFF
|
A/C SIG OFF
|
ON
|
A/C SIG ON
|
|
NG |
 |
|
|
|
| OK |
|
 |
|
| PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE |
|
| 2. INSPECT ECM (AC1 VOLTAGE) |
 |
- Start the engine.
Measure the voltage of the ECM connector.
- Standard voltage:
Tester Connection
|
Connection
|
Specified Condition
|
E21-2 (AC1) - Body ground
|
A/C compressor ON
|
Below 1.5 V
|
E21-2 (AC1) - Body ground
|
A/C compressor OFF
|
7.5 to 14 V
|
|
NG |
 |
|
|
|
| OK |
|
 |
|
|
| 3. CHECK WIRE HARNESS (ECM - AIR CONDITIONING AMPLIFIER) |
 |
- Disconnect the A9 A/C amplifier connector.
Disconnect the E21 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
|
Specified Condition
|
A9-14 (AC1)* - E21-2 (AC1)
|
Below 1 Ω
|
E21-2 (AC1) - Body ground
|
10 kΩ or higher
|
- HINT:
- *: Terminal arrangement (Click here).
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS AND CONNECTOR |
|
|
| OK |
|
 |
|
| REPLACE AIR CONDITIONING AMPLIFIER |
|
When not using intelligent tester:
| 1. INSPECT ECM (AC1 VOLTAGE) |
 |
- Start the engine.
Measure the voltage of the ECM connector.
- Standard voltage:
Tester Connection
|
Connection
|
Specified Condition
|
E21-2 (AC1) - Body ground
|
A/C compressor ON
|
Below 1.5 V
|
E21-2 (AC1) - Body ground
|
A/C compressor OFF
|
7.5 to 14 V
|
|
OK |
 |
|
| PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE |
|
|
| NG |
|
 |
|
| 2. CHECK WIRE HARNESS (ECM - AIR CONDITIONING AMPLIFIER) |
 |
- Disconnect the A9 A/C amplifier connector.
Disconnect the E21 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
|
Specified Condition
|
A9-4 (AC1)* - E21-2 (AC1)
|
Below 1 Ω
|
E21-2 (AC1) - Body ground
|
10 kΩ or higher
|
- HINT:
- *: Terminal arrangement (Click here).
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS AND CONNECTOR |
|
|
| OK |
|
 |
|
| REPLACE AIR CONDITIONING AMPLIFIER |
|