2014 Hilux · Service Manual ENGINE

Air Conditioning Cut Control Circuit

Circuit diagnosis · Vehicles built from Jun 2011

DESCRIPTION

This circuit cuts air conditioning operation during vehicle acceleration in order to increase acceleration performance. During acceleration with the vehicle speed at 30 km/h (19 mph) or less and accelerator pedal opening angle at 45° or more, the A/C magnetic switch is turned off for several seconds.
The air conditioning is also controlled by the ECM outputting the engine coolant temperature to A/C amplifier.

WIRING DIAGRAM

A261035E01

INSPECTION PROCEDURE


When using intelligent tester:


1. READ VALUE USING INTELLIGENT TESTER (CHECK OPERATION AIR CONDITIONING CUT CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and air conditioning switch ON.

    HINT:
    A/C magnetic clutch is turned ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / A/C Cut SIG.

  1. Check operation of A/C magnetic clutch cut when air conditioning cut control is operated by the intelligent tester.

    OK:
    A/C magnetic clutch is turned OFF.



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2. INSPECT ECM (ACT VOLTAGE)

  1. A062416E56
    Start the engine.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E21-8 (ACT) - Body ground
    Engine at idling
    9 to 14 V
    E21-8 (ACT) - Body ground
    Ignition switch ON, Engine stopped
    0 to 3 V



OK
REPLACE ECM
NG


3. CHECK WIRE HARNESS (ECM - AIR CONDITIONING AMPLIFIER)

  1. A062418E10
    Disconnect the A9 A/C amplifier connector.

  1. Disconnect the E21 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A9-2 (ACT)* - E21-8 (ACT)
    Below 1 Ω
    E21-8 (ACT) - Body ground
    10 kΩ or higher

    HINT:
    *: Terminal arrangement (Click here).



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

CHECK AND REPLACE AIR CONDITIONING AMPLIFIER


When not using intelligent tester:


1. CHECK ECM (ACT VOLTAGE)

  1. A062416E56
    Start the engine.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E21-8 (ACT) - Body ground
    Engine at idling
    9 to 14 V
    E21-8 (ACT) - Body ground
    Ignition switch ON, Engine stopped
    0 to 3 V



NG
Go to step 2
OK

REPLACE ECM

2. CHECK WIRE HARNESS (ECM - AIR CONDITIONING AMPLIFIER)

  1. A062418E10
    Disconnect the A9 A/C amplifier connector.

  1. Disconnect the E21 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A9-2 (ACT)* - E21-8 (ACT)
    Below 1 Ω
    E21-8 (ACT) - Body ground
    10 kΩ or higher

    HINT:
    *: Terminal arrangement (Click here).



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

CHECK AND REPLACE AIR CONDITIONING AMPLIFIER


← Air Conditioning Signal Circuit (from Jun 2011)Brake Override System (Jun 2011 – Oct 2011) →