C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction
Diagnostic trouble codes · Vehicles built Nov 2011 – Mar 2012
Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Refer to DTCs C1421, C1423 and C1424 (Click here).| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1422 |
When the stop light switch is off, the PMC terminal voltage is higher than 0.86 V for 5 seconds or more. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the brake actuator assembly, perform calibration (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- Before disconnecting the connector, make sure that there are no problems with the connection.
- After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
- After replacing the brake actuator assembly, perform calibration (Click here).
| 1. CHECK DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).
Check for DTCs (Click here).
Result Result
Proceed to
DTC C1422 is output
A
DTC C1422 and C1425 are output
B
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light SW
Stop light switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Check that the stop light switch display observed on the intelligent tester changes according to the brake pedal operation.
- OK:
- The intelligent tester displays ON or OFF according to brake pedal operation.
|
|
||||
| OK | |
| 3. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION |
Turn the ignition switch off.
Check the brake pedal height and stop light switch installation (Click here).
- OK:
- The brake pedal height and stop light switch installation are normal.
|
|
||||
| OK | |
| 4. RECONFIRM DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC C1422 is not output
A
DTC C1422 is output
for LHD
B
for RHD
C
|
|
||||
|
|
||||
| A | ||
| ||
| 5. CHECK TERMINAL VOLTAGE (STOP LIGHT POWER SOURCE CIRCUIT) |
Turn the ignition switch off.
Disconnect the stop light switch connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
S14-2 - Body ground
Always
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Stop Light Switch)
|
|
||||
| OK | |
| 6. INSPECT STOP LIGHT SWITCH ASSEMBLY |
Turn the ignition switch off.
Remove the stop light switch assembly (Click here).
Inspect the stop light switch assembly (Click here).
|
|
||||
| OK | |
| 7. CHECK TERMINAL VOLTAGE (STP TERMINAL) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
S35-2 (STP) - Body ground
Brake pedal depressed
8 to 14 V
Brake pedal released
Below 1.5 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
Result Result
Proceed to
NG
A
OK
for LHD
B
for RHD
C
|
|
||||
|
|
||||
| A | ||
| ||
