C1429 Open or Short in Brake Pedal Load Sensing Switch
Diagnostic trouble codes · Vehicles built Nov 2011 – Mar 2012
Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The brake pedal load sensing switch operates when the brake pedal is depressed with a force exceeding a predetermined level.The skid control ECU (brake actuator assembly) detects if the brake pedal is depressed or not via this circuit.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1429 |
An open or short in the brake pedal load sensing switch continues for 0.3 seconds or more. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the brake actuator assembly, perform calibration (Click here).
- Before disconnecting the connector, make sure that there are no problems with the connection.
- After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
- After replacing the brake actuator assembly, perform calibration (Click here).
- HINT:
- When DTC C1425 is output together with DTC C1429, inspect and repair the trouble areas indicated by DTC C1425 first (Click here).
| 1. READ VALUE USING INTELLIGENT TESTER (BRAKE PEDAL LOAD SENSING SW) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Brake Pedal Load Sensing SW
Brake pedal load sensing switch / ON or OFF
ON: Brake pedal depressed beyond specified point
OFF: Brake pedal not depressed beyond specified point
-
Check that the brake pedal load sensing switch display observed on the intelligent tester changes according to the brake pedal operation.
- OK:
- The intelligent tester displays ON or OFF according to brake pedal operation.
|
|
||||
| OK | |
| 2. RECONFIRM DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Start the engine.
Depress the brake pedal several times.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
for LHD
B
for RHD
C
|
|
||||
|
|
||||
| A | ||
| ||
| 3. INSPECT BRAKE PEDAL LOAD SENSING SWITCH |


| *1 |
Brake Pedal Load Sensing Switch |
*2 |
Brake with Switch Pedal Sub-assembly |
| *a |
Component without harness connected (Brake Pedal Load Sensing Switch) |
*b |
Brake Pedal Released (Closed) |
| *c |
Brake Pedal Depressed (Open) |
- |
- |
- NOTICE:
- Do not remove the brake pedal load sensing switch from the brake with switch pedal sub-assembly.
- When there is a malfunction in the brake pedal load sensing switch, replace the brake with switch pedal sub-assembly.
- Do not remove the brake pedal load sensing switch from the brake with switch pedal sub-assembly.
Turn the ignition switch off.
Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
2 - 1
Brake pedal depressed
950 to 1050 Ω
Brake pedal released
203 to 223 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S35-27 (FSW+) - B8-2
Always
Below 1 Ω
S35-27 (FSW+) - Body ground
Always
10 kΩ or higher
B8-1 - Body ground
Always
Below 1 Ω
Result Result
Proceed to
NG
A
OK
for LHD
B
for RHD
C
|
|
||||
|
|
||||
| A | ||
| ||
