2014 Hilux · Service Manual BRAKE

C1429 Open or Short in Brake Pedal Load Sensing Switch

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The brake pedal load sensing switch operates when the brake pedal is depressed with a force exceeding a predetermined level.
The skid control ECU (brake actuator assembly) detects if the brake pedal is depressed or not via this circuit.
DTC Code
DTC Detection Condition
Trouble Area
C1429
An open or short in the brake pedal load sensing switch continues for 0.3 seconds or more.
  1. Brake pedal load sensing switch (Brake with switch pedal sub-assembly)
  2. Brake pedal load sensing switch circuit
  3. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM

C194456E10

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Click here).
  2. Before disconnecting the connector, make sure that there are no problems with the connection.
  3. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.

HINT:
When DTC C1425 is output together with DTC C1429, inspect and repair the trouble areas indicated by DTC C1425 first (Click here).


1. READ VALUE USING INTELLIGENT TESTER (BRAKE PEDAL LOAD SENSING SW)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Brake Pedal Load Sensing SW
    Brake pedal load sensing switch / ON or OFF
    ON: Brake pedal depressed beyond specified point
    OFF: Brake pedal not depressed beyond specified point
    -

  1. Check that the brake pedal load sensing switch display observed on the intelligent tester changes according to the brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.



NG
Go to step 3
OK


2. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Depress the brake pedal several times.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    for LHD
    B
    for RHD
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

3. INSPECT BRAKE PEDAL LOAD SENSING SWITCH
C190633E02
Text in Illustration  
*1
Brake Pedal Load Sensing Switch
*2
Brake with Switch Pedal Sub-assembly
*a
Component without harness connected
(Brake Pedal Load Sensing Switch)
*b
Brake Pedal Released (Closed)
*c
Brake Pedal Depressed (Open)
-
-

NOTICE:
  1. Do not remove the brake pedal load sensing switch from the brake with switch pedal sub-assembly.
  2. When there is a malfunction in the brake pedal load sensing switch, replace the brake with switch pedal sub-assembly.

  1. Turn the ignition switch off.

  1. Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - 1
    Brake pedal depressed
    950 to 1050 Ω
    Brake pedal released
    203 to 223 Ω



NG
REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-27 (FSW+) - B8-2
    Always
    Below 1 Ω
    S35-27 (FSW+) - Body ground
    Always
    10 kΩ or higher
    B8-1 - Body ground
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK
    for LHD
    B
    for RHD
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR


← C1429 Open or Short in Brake Pedal Load Sensing Switch (Aug 2013 – Jul 2014)C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction (+ C1431) (Jun 2011 – Oct 2011) →