2014 Hilux · Service Manual BRAKE

TC and CG Terminal Circuit

Circuit diagnosis · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to output the DTCs by blinking the ABS warning light and VSC OFF indicator light.

WIRING DIAGRAM

C245070E01

HINT:
When the warning light and indicator light continue to blink, there may be a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs.


INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Click here).
  2. Before disconnecting the connector, make sure that there are no problems with the connection.
  3. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


2. INSPECT DLC3

  1. C146309E17
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D1-13 (TC) - D1-4 (CG)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 4
OK


3. CHECK ECM (DLC3 INPUT)
SST
09843-18040  

  1. C146309E17
    Turn the ignition switch off.

  1. Connect the ECM connector.

  1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

    Text in Illustration 
    *a
    Front view of DLC3

  1. Turn the ignition switch to ON.

  1. Check that the MIL is blinking.

    Result 
    Result
    Proceed to
    MIL is not blinking
    A
    MIL is blinking
    for LHD
    B
    for RHD
    C

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

REPAIR OR REPLACE WIRE HARNESS OR ECM

4. CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
  1. Turn the ignition switch off.

  1. for 1KD-FTV (for DPF) and 2KD-FTV (for DPF):Disconnect the E30 ECM connector.for 1KD-FTV (except DPF) and 2KD-FTV (except DPF):Disconnect the E5 ECM connector.for 1GR-FE:Disconnect the E14 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV (for DPF) and 2KD-FTV (for DPF) 
    Tester Connection
    Condition
    Specified Condition
    D1-13 (TC) - E30-23 (TC)
    Always
    Below 1 Ω
    D1-13 (TC) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (except DPF) and 2KD-FTV (except DPF) 
    Tester Connection
    Condition
    Specified Condition
    D1-13 (TC) - E5-11 (TC)
    Always
    Below 1 Ω
    D1-13 (TC) - Body ground
    Always
    10 kΩ or higher
    for 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    D1-13 (TC) - E14-23 (TC)
    Always
    Below 1 Ω
    D1-13 (TC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-4 (CG) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK ECM (DLC3 INPUT)
SST
09843-18040  

  1. C146309E17
    Turn the ignition switch off.

  1. Connect the ECM connector.

  1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

    Text in Illustration 
    *a
    Front view of DLC3

  1. Turn the ignition switch to ON.

  1. Check that the MIL is blinking.

    Result 
    Result
    Proceed to
    MIL is not blinking
    A
    MIL is blinking
    for LHD
    B
    for RHD
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

REPAIR OR REPLACE WIRE HARNESS OR ECM


← TC and CG Terminal Circuit (Apr 2012 – Jul 2012)TC and CG Terminal Circuit (Aug 2013 – Jul 2014) →