B2796 No Communication in Immobiliser System
Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013
Also covers:
- B2798 Communication Malfunction No. 2
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
DESCRIPTION
DTC B2796 is stored when a key is inserted into the ignition key cylinder but no communication occurs between the key and transponder key ECU assembly.DTC B2798 is stored when a key is inserted into the ignition key cylinder but a communication error occurs between the key and transponder key ECU assembly.
| DTC Code |
DTC Detection Condition |
Trouble Area |
DTC Output Confirmation Operation |
| B2796 |
The key code cannot be transmitted (1 trip detection logic*). |
|
Insert the key into the ignition key cylinder |
| B2798 |
Key code identification cannot be completed within the specified time (1 trip detection logic*). |
Key |
Insert the key into the ignition key cylinder |
- *: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected |
Fail-safe Operation when Malfunction Detected |
| Engine cannot be started. |
- |
| DTC Code |
Data List and Active Test |
| B2796 |
Response |
| B2798 |
Frame Error |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the transponder key ECU assembly, refer to the Service Bulletin.
- After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
- When replacing the transponder key ECU assembly, refer to the Service Bulletin.
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2796 or B2798 is not output.
|
|
||||
| OK | ||
| ||
| 3. READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM) |
Use the Data List to check if the engine immobiliser system is functioning properly (Click here).
Immobiliser Item
Measurement Item/Range
Normal Condition
Diagnostic Note
Immobiliser
Engine immobiliser system status determined by transponder key ECU assembly / Set or Unset
Set: Engine immobiliser set (engine start prohibited [no key in ignition key cylinder])
Unset: Engine immobiliser unset (engine start permitted [key inserted in ignition key cylinder])
When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the transponder key ECU assembly.
- OK:
- Set (the key is not inserted in the ignition key cylinder) and Unset (the key is inserted in the ignition key cylinder) appear on the screen according to the key insertion condition.
|
|
||||
| OK | ||
| ||
| 4. CHECK WHETHER ENGINE STARTS WITH OTHER KEY |
Check whether the engine starts with an already registered vehicle key.
- OK:
- Engine starts.
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER) |
Disconnect the T21 transponder key ECU assembly connector.
Disconnect the T20 transponder key amplifier connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
T21-14 (VC5) - T20-1 (VC5)
Always
Below 1 Ω
T21-15 (CODE) - T20-4 (CODE)
Always
Below 1 Ω
T21-4 (TXCT) - T20-5 (TXCT)
Always
Below 1 Ω
T21-5 (AGND) - T20-7 (AGND)
Always
Below 1 Ω
T21-14 (VC5) or T20-1 (VC5) - Body ground
Always
10 kΩ or higher
T21-15 (CODE) or T20-4 (CODE) - Body ground
Always
10 kΩ or higher
T21-4 (TXCT) or T20-5 (TXCT) - Body ground
Always
10 kΩ or higher
T21-5 (AGND) or T20-7 (AGND) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. REPLACE TRANSPONDER KEY AMPLIFIER |
Temporally replace the transponder key amplifier with a new or normally functioning one (Click here).
| NEXT | |
| 7. CHECK WHETHER ENGINE STARTS |
Check that the engine starts normally.
- OK:
- Engine starts.
|
|
||||
| OK | ||
| ||
