DESCRIPTION
When the engine is cranked, the intake air flow becomes slow, so fuel vaporization is poor. A rich mixture is therefore necessary in order to achieve good startability. While the engine is being cranked, the battery voltage is applied to terminal STA of the ECM. The starter signal is mainly used to increase the fuel injection volume for starting and after-start injection control.WIRING DIAGRAM


INSPECTION PROCEDURE
When using intelligent tester:
| 1. READ DATA LIST (STA SIGNAL) |
 |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned to ON and START.
- Result:
Ignition Switch Position
|
STA Signal
|
Proceed to
|
ON → START
|
for A/T: Display does not change for OFF → ON
|
A
|
for M/T: Display does not change for OFF → ON
|
B
|
Display changes from OFF → ON
|
C
|
|
B |
 |
|
|
|
|
C |
 |
|
| PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE |
|
|
| A |
|
 |
|
| 2. INSPECT PARK/NEUTRAL POSITION SWITCH |
 |
Move the shift lever to the P or N position.
Disconnect the N1 Park/Neutral Position (PNP) switch connector.
Measure the resistance of the PNP switch.
- Standard:
Tester Connection
|
Shift Position
|
Specified Condition
|
4 (B) - 5 (L)
|
P or N
|
Below 1 Ω
|
4 (B) - 5 (L)
|
Except P or N
|
10 kΩ or higher
|
|
NG |
 |
|
| REPLACE PARK/NEUTRAL POSITION SWITCH (GO TO NEXT STEP AFTER REPLACEMENT) |
|
|
| OK |
|
 |
|
| 3. CHECK WIRE HARNESS (ECM - IGNITION SWITCH) |
 |
Disconnect the E9 ECM connector.
Disconnect the I6 ignition switch connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
|
Specified Condition
|
E9-12 (STA) - I6-7 (ST2)
|
Below 1 Ω
|
E9-12 (STA) or I6-7 (ST2) - Body ground
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS AND CONNECTOR |
|
|
| OK |
|
 |
|
| 4. INSPECT IGNITION SWITCH |
 |
Inspect the ignition switch (Click here).
|
NG |
 |
|
| REPLACE IGNITION SWITCH (GO TO NEXT STEP AFTER REPLACEMENT) |
|
|
| OK |
|
 |
|
| 5. DATA LIST (STA SIGNAL) |
 |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned to ON and START.
- OK:
Ignition Switch Position
|
STA Signal
|
ON → START
|
Display changes from OFF → ON
|
|
NG |
 |
|
|
|
| OK |
|
 |
|
|
When not using intelligent tester:
| 1. CHECK ECM (STA VOLTAGE) |
 |
Turn the ignition switch ON.
Measure the voltage of the ECM connectors.
- Standard voltage:
Tester Connection
|
Specified Condition
|
E9-12 (STA) - E12-3 (E1)
|
0 V
|
Measure the voltage of the ECM connectors when the engine is cranked.
- Standard voltage:
Tester Connection
|
Specified Condition
|
E9-12 (STA) - E12-3 (E1)
|
6 V or more
|
Result
Result
|
Proceed to
|
NG for A/T
|
A
|
NG for M/T
|
B
|
OK
|
C
|
|
B |
 |
|
|
|
|
C |
 |
|
| PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE |
|
|
| A |
|
 |
|
| 2. INSPECT PARK/NEUTRAL POSITION SWITCH |
 |
Move the shift lever to the P or N position.
Disconnect the N1 Park/Neutral Position (PNP) switch connector.
Measure the resistance of the PNP switch.
- Standard:
Tester Connection
|
Shift Position
|
Specified Condition
|
4 (B) - 5 (L)
|
P or N
|
Below 1 Ω
|
4 (B) - 5 (L)
|
Except P or N
|
10 kΩ or higher
|
|
NG |
 |
|
| REPLACE PARK/NEUTRAL POSITION SWITCH |
|
|
| OK |
|
 |
|
| 3. CHECK WIRE HARNESS (ECM - IGNITION SWITCH) |
 |
Disconnect the E9 ECM connector.
Disconnect the I6 ignition switch connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
|
Specified Condition
|
E9-12 (STA) - I6-7 (ST2)
|
Below 1 Ω
|
E9-12 (STA) or I6-7 (ST2) - Body ground
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS AND CONNECTOR |
|
|
| OK |
|
 |
|
| 4. INSPECT IGNITION SWITCH |
 |
Inspect the ignition switch (Click here).
|
NG |
 |
|
|
|
| OK |
|
 |
|
|