Fuel Injector Circuit
Circuit diagnosis · Vehicles built from Jun 2011
DESCRIPTION
The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK ECM (#10, #20, #30, #40 VOLTAGE) |
![]() ![]() |
Turn the ignition switch ON.
Measure the voltage of the ECM connectors.
- Standard voltage:
Tester Connection
Specified Condition
E11-6 (#10) - E12-7 (E01)
9 to 14 V
E11-5 (#20) - E12-7 (E01)
9 to 14 V
E11-2 (#30) - E12-7 (E01)
9 to 14 V
E11-1 (#40) - E12-7 (E01)
9 to 14 V


- HINT:
- Reference: Inspection using the oscilloscope.
- Check the waveform of the ECM connector.
Tester Connection
Specified Condition
E11-6 (#10) - E12-7 (E01)
Correct waveform is as shown
E11-5 (#20) - E12-7 (E01)
Correct waveform is as shown
E11-2 (#30) - E12-7 (E01)
Correct waveform is as shown
E11-1 (#40) - E12-7 (E01)
Correct waveform is as shown
Tool Setting
Condition
20V/DIV., 100 or 1 msec./DIV.
Idling
|
|
||||
| NG | |
| 2. INSPECT FUEL INJECTOR ASSEMBLY (RESISTANCE) |
Inspect the fuel injector (Click here).
|
|
||||
| OK | |
| 3. INSPECT FUSE (INJ) |
![]() ![]() |
Remove the INJ fuse from the instrument panel junction block.
Measure the resistance of the fuse.
- Standard:
- Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK WIRE HARNESS OF MISFIRING CYLINDER (INJECTOR - ECM, INJECTOR - INJ FUSE) |
![]() ![]() |
Check the wire harness between the injector and ECM.
Disconnect the F5, F6, F7 and/or F8 injector connectors.
Disconnect the E11 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
F5-2 - E11-6 (#10)
Below 1 Ω
F6-2 - E11-5 (#20)
Below 1 Ω
F7-2 - E11-2 (#30)
Below 1 Ω
F8-2 - E11-1 (#40)
Below 1 Ω
F5-2 or E11-6 (#10) - Body ground
10 kΩ or higher
F6-2 or E11-5 (#20) - Body ground
10 kΩ or higher
F7-2 or E11-2 (#30) - Body ground
10 kΩ or higher
F8-2 or E11-1 (#40) - Body ground
10 kΩ or higher
Check the wire harness between the injector and INJ fuse.
Disconnect the F5, F6, F7 and F8 injector connectors.
Remove the INJ fuse from the instrument panel junction block.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
F5-1 - J/B INJ fuse terminal 2
Below 1 Ω
F6-1 - J/B INJ fuse terminal 2
Below 1 Ω
F7-1 - J/B INJ fuse terminal 2
Below 1 Ω
F8-1 - J/B INJ fuse terminal 2
Below 1 Ω
F5-1 or J/B INJ fuse terminal 2 - Body ground
10 kΩ or higher
F6-1 or J/B INJ fuse terminal 2 - Body ground
10 kΩ or higher
F7-1 or J/B INJ fuse terminal 2 - Body ground
10 kΩ or higher
F8-1 or J/B INJ fuse terminal 2 - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK WIRE HARNESS (IGNITION SWITCH - INJ FUSE) |
![]() ![]() |
Disconnect the I6 ignition switch connector.
Remove the INJ fuse from the instrument panel junction block.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
I6-6 (IG2) - J/B INJ fuse terminal 1
Below 1 Ω
I6-6 (IG2) or J/B INJ fuse terminal 1 - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 6. CHECK WIRE HARNESS (ECM - BODY GROUND) |
![]() ![]() |
Disconnect the E12 ECM connector.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E12-7 (E01) - Body ground
Below 1 Ω
E12-6 (E02) - Body ground
Below 1 Ω
|
|
||||
| OK | |
| 7. INSPECT FUEL INJECTOR ASSEMBLY (FUEL INJECTION VOLUME) |
Inspect the fuel injector (Click here).
|
|
||||
| OK | ||
| ||





