DESCRIPTION
When the engine is cranked, current flows from terminal ST2 of the ignition switch to the starter relay (Marking: ST) coil, and current also flows to terminal STA of the ECM (STA signal).When the STA signal and NE signal are transmitted to the ECM, the power transistor (Tr) is turned ON, current flows to the circuit opening relay (Marking: C/OPN) coil, the relay switches on, power is supplied to the fuel pump and the fuel pump operates.While the NE signal is generated (when engine running), the ECM keeps Tr ON (circuit opening relay ON) and the fuel pump also keeps operating.

WIRING DIAGRAM


INSPECTION PROCEDURE
When using intelligent tester:
| 1. PERFORM ACTIVE TEST (OPERATE C/OPN RELAY) |
 |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Fuel Pump.
Check the operation of the relay while operating it using the intelligent tester.
- OK:
- Operating noise can be heard from the fuel pump.
|
OK |
 |
|
| PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE |
|
|
| NG |
|
 |
|
| 2. CHECK ECM POWER SOURCE CIRCUIT |
 |
Refer to ECM power source circuit (Click here).
|
NG |
 |
|
| REPAIR OR REPLACE POWER SOURCE CIRCUIT |
|
|
| OK |
|
 |
|
| 3. CHECK ECM (FC VOLTAGE) |
 |
Turn the ignition switch ON.
Measure the voltage of the ECM connectors.
- Standard voltage:
Tester Connection
|
Specified Condition
|
E9-25 (FC) - E12-3 (E1)
|
9 to 14 V
|
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 4. CHECK INTEGRATION NO.1 RELAY (C/OPN RELAY) |
 |
Remove the integration relay from the engine room junction block (Click here).
Measure the voltage of the C/OPN relay.
- Standard voltage:
Tester Connection
|
Condition
|
Specified Condition
|
1J-8 - Body ground
|
Engine cranking
|
10 to 14 V
|
|
NG |
 |
|
| REPLACE INTEGRATION NO.1 RELAY |
|
|
| OK |
|
 |
|
| 5. INSPECT FUEL PUMP |
 |
Inspect the fuel pump (Click here).
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 6. CHECK WIRE HARNESS (FUEL PUMP - INTEGRATION RELAY (C/OPN RELAY), BODY GROUND) |
 |
Disconnect the 1J integration relay connector from the engine room junction block (Click here).
Disconnect the F15 fuel pump connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
|
Specified Condition
|
1J-8 - F15-4
|
Below 1 Ω
|
F15-5 - Body ground
|
Below 1 Ω
|
1J-8 or F15-4 - Body ground
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS AND CONNECTOR |
|
|
| OK |
|
 |
|
|
| 7. CHECK WIRE HARNESS (INTEGRATION RELAY (C/OPN RELAY) - ECM) |
 |
Disconnect the 1J integration relay connector from the engine room junction block (Click here).
Disconnect the E9 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
|
Specified Condition
|
1J-7 - E9-25 (FC)
|
Below 1 Ω
|
1J-7 or E9-25 (FC) - Body ground
|
10 kΩ or higher
|
Turn the ignition switch ON.
Measure the voltage of the C/OPN relay.
- Standard voltage:
Tester Connection
|
Specified Condition
|
1J-6 - Body ground
|
9 to 14 V
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS AND CONNECTOR |
|
|
| OK |
|
 |
|
|
When not using intelligent tester:
| 1. INSPECT FUEL PUMP (OPERATION) |
 |
Operation of fuel pump (Click here).
|
OK |
 |
|
| PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE |
|
|
| NG |
|
 |
|
| 2. CHECK ECM POWER SOURCE CIRCUIT |
 |
Refer to ECM power source circuit (Click here).
|
NG |
 |
|
| REPAIR OR REPLACE POWER SOURCE CIRCUIT |
|
|
| OK |
|
 |
|
| 3. CHECK ECM (FC VOLTAGE) |
 |
Turn the ignition switch ON.
Measure the voltage of the ECM connectors.
- Standard voltage:
Tester Connection
|
Specified Condition
|
E9-25 (FC) - E12-3 (E1)
|
9 to 14 V
|
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 4. CHECK INTEGRATION NO.1 RELAY (C/OPN RELAY) |
 |
Remove the integration relay from the engine room junction block (Click here).
Measure the voltage of the C/OPN relay.
- Standard voltage:
Tester Connection
|
Condition
|
Specified Condition
|
1J-8 - Body ground
|
Engine cranking
|
10 to 14 V
|
|
NG |
 |
|
| REPLACE INTEGRATION NO.1 RELAY |
|
|
| OK |
|
 |
|
| 5. INSPECT FUEL PUMP |
 |
Inspect the fuel pump (Click here).
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 6. CHECK WIRE HARNESS (FUEL PUMP - INTEGRATION RELAY (C/OPN RELAY), BODY GROUND) |
 |
Disconnect the 1J integration relay connector from the engine room junction block (Click here).
Disconnect the F15 fuel pump connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
|
Specified Condition
|
1J-8 - F15-4
|
Below 1 Ω
|
F15-5 - Body ground
|
Below 1 Ω
|
1J-8 or F15-4 - Body ground
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS AND CONNECTOR |
|
|
| OK |
|
 |
|
|
| 7. CHECK WIRE HARNESS (INTEGRATION RELAY (C/OPN RELAY) - ECM) |
 |
Disconnect the 1J integration relay connector from the engine room junction block (Click here).
Disconnect the E9 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
|
Specified Condition
|
1J-7 - E9-25 (FC)
|
Below 1 Ω
|
1J-7 or E9-25 (FC) - Body ground
|
10 kΩ or higher
|
Turn the ignition switch ON.
Measure the voltage of the C/OPN relay.
- Standard voltage:
Tester Connection
|
Specified Condition
|
1J-6 - Body ground
|
9 to 14 V
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS AND CONNECTOR |
|
|
| OK |
|
 |
|
|