2014 Hilux · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2011


1. REMOVE CENTER NO. 1 SUPPORT BEARING ASSEMBLY

F049877E01
  1. Place matchmarks on the flanges.

  1. Remove the 4 nuts and 4 washers.

  1. Separate the propeller shaft and intermediate shaft.

  1. A098690E01
    Fix the flange coupling at the center bearing section in a vise.

  1. Using a chisel and hammer, loosen the staked part of the lock nut.

    NOTICE:
    Loosen the staked part of the lock nut completely. If not, the screw of the intermediate shaft may be damaged.

  1. F049875E01
    Using SST and a socket wrench, remove the nut and washer.
    SST
    09330-00021  

  1. F049874E01
    Place matchmarks on the intermediate shaft and flange coupling.

  1. F049876E01
    Using SST, remove the flange coupling from the intermediate shaft.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)

  1. Remove the center support bearing.


2. INSPECT PROPELLER SHAFT AND INTERMEDIATE SHAFT

C061260E02
  1. Using a dial indicator, measure the propeller shaft and intermediate shaft runout.

    Maximum runout:
    Item
    Specified Condition
    Propeller shaft
    0.3 mm (0.012 in.)
    Intermediate shaft
    0.5 mm (0.02 in.)

    If the shaft runout is greater than the maximum, replace the shaft.


3. INSPECT UNIVERSAL JOINT SPIDER ASSEMBLY
  1. Check the spider bearings for wear or damage.

  1. Check each spider bearing's axial play by turning the yoke while holding the shaft tightly.

    Maximum bearing axial play:
    0 to 0.05 mm (0 to 0.002 in.)

    If the bearing axial play is greater than the maximum, replace the spider bearing.


4. INSPECT CENTER NO. 1 SUPPORT BEARING ASSEMBLY

F049879E01
  1. When turning the center bearing with your hand, check that it turns smoothly without catching, and that there are no cracks or damage.
    If there are any defects, replace it.
    If there is any damage to the lip of the center bearing case, replace it.


5. REMOVE UNIVERSAL JOINT SPIDER ASSEMBLY

F015023E01
  1. Place matchmarks on the flange yoke and shaft.

  1. C061264E01
    Using a brass bar and hammer, slightly tap in the spider bearing outer races.

  1. Using 2 screwdrivers, remove the 4 snap rings from the grooves.

  1. F015025E01
    Clamp the propeller shaft in a vise between aluminum plates.

  1. Using SST, push the sleeve yoke side spider bearing until: 1) the spider almost touches the sleeve yoke or propeller shaft, and 2) the spider bearing on the opposite side is partially pushed out.

    SST
    09332-25010  

    HINT:
    Before installing SST, sufficiently raise the part labeled A. If part A is too low, SST may be difficult to install.

  1. F044192E01
    Clamp the pushed out spider bearing outer race in a vise and tap the propeller shaft to remove the spider bearing.

    NOTICE:
    Do not tap the shaft tube.

    HINT:
    Remove the spider bearing from the opposite side of the spider using the same procedure.

  1. Separate the flange yoke and spider from the propeller shaft.

  1. F015030E01
    Reinstall the 2 removed spider bearings to the spider and clamp the spider bearings in a vise.

  1. Using SST, push the flange yoke side spider bearing until: 1) the spider almost touches the flange yoke, and 2) the spider bearing on the opposite side is partially pushed out.

    SST
    09332-25010  

    HINT:
    Before installing SST, sufficiently raise the part labeled A. If part A is too low, SST may be difficult to install.

  1. F044193E01
    Clamp the pushed out spider bearing outer race in a vise and tap the flange yoke to remove the spider bearing.

    HINT:
    Remove the spider bearing from the opposite side of the spider using the same procedure.

  1. Separate the spider from the flange yoke.

    HINT:
    Perform the removal of the other universal joint spider(s) using the same procedures.

← REMOVAL (from Jun 2011)INSPECTION (from Jun 2011) →