INSTALLATION
Removal / installation · Vehicles built from Jun 2011
- HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
- A bolt without a torque specification is shown in the standard bolt chart (Click here).
- Use the same procedures for the RH side and LH side.
| 1. INSTALL FRONT AXLE HUB INNER BEARING |
![]() ![]() |
Using SST and a press, press a new bearing into the steering knuckle.
- SST
- 09527-17011
09950-60020 (09951-00910)
Using snap ring pliers, install a new snap ring.
| 2. INSTALL FRONT AXLE HUB OIL SEAL |
![]() ![]() |
Using SST and a plastic-faced hammer, tap in a new oil seal.
- SST
- 09223-15030
09527-17011
Apply MP grease to the lip of the oil seal.
| 3. INSTALL AXLE HUB TO STEERING KNUCKLE |
![]() ![]() |
Install the dust cover to the steering knuckle with the 3 bolts.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Using SST and a press, press the axle hub into the steering knuckle.
- SST
- 09223-00010
| 4. INSTALL FRONT AXLE HUB NUT AND ABS SPEED SENSOR ROTOR OR SPACER |
![]() ![]() |
w/ ABS:
Install the ABS speed sensor rotor.
w/o ABS:
Install the spacer.
Install a new nut to the axle hub.
- Torque:
- 199 N*m{ 2,029 kgf*cm , 147 ft.*lbf }
Using a chisel and hammer, stake the nut.
- NOTICE:
- Do not scratch the serration of the speed sensor rotor.
| 5. INSTALL KNUCKLE GREASE RETAINER CAP |
![]() ![]() |
Using a brass bar and hammer, install the knuckle grease retainer cap.
- NOTICE:
- Do not damage the knuckle grease retainer cap.
| 6. INSTALL FRONT AXLE HUB ASSEMBLY |
| 7. CONNECT FRONT SUSPENSION UPPER ARM ASSEMBLY LH |
![]() ![]() |
Connect the upper arm with the nut.
- Torque:
- 110 N*m{ 1,122 kgf*cm , 81 ft.*lbf }
Install a new clip.
- NOTICE:
- If the holes for the clip are not aligned, tighten the nut an additional 60°.
| 8. CONNECT FRONT SUSPENSION LOWER ARM ASSEMBLY WITH ATTACHMENT LH |
![]() ![]() |
Connect the suspension arm with the 2 bolts.
- Torque:
- 160 N*m{ 1,632 kgf*cm , 118 ft.*lbf }
| 9. INSTALL TIE ROD END SUB-ASSEMBLY |
![]() ![]() |
Connect the tie rod end with the nut.
- Torque:
- 49 N*m{ 500 kgf*cm , 36 ft.*lbf }
Install a new cotter pin.
- NOTICE:
- If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.
| 10. INSTALL FRONT DISC |
| 11. INSTALL FRONT SPEED SENSOR LH |
![]() ![]() |
Install the speed sensor with the bolt.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
Connect the 3 clamps with the 3 bolts.
- Torque:
- 32 N*m{ 326 kgf*cm , 24 ft.*lbf }
| 12. INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH |
Install the brake cylinder with the 2 bolts.

- Torque:
- 126 N*m{ 1,285 kgf*cm , 93 ft.*lbf }
Connect the brake hose to the brake cylinder with the union bolt and a new gasket.
- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
| 13. BLEED BRAKE LINE |
for TSAM Made:
(Click here)
for TMT Made :
(Click here)
w/ VSC:
(Click here)
| 14. INSTALL FRONT WHEEL |
- Torque:
- 152 N*m{ 1,550 kgf*cm , 112 ft.*lbf } for steel type
- 121 N*m{ 1,234 kgf*cm , 89 ft.*lbf } for aluminum type
| 15. CHECK ABS SPEED SENSOR SIGNAL |
Check the ABS speed sensor signal (Click here).









