C1243/43 Acceleration Sensor Stuck Malfunction
Diagnostic trouble codes · Vehicles built from Jun 2011
Also covers:
- C1244/44 Open or Short in Deceleration Sensor Circuit
- C1245/45 Acceleration Sensor Output Malfunction
- C1279/79 Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)
DESCRIPTION
This sensor detects vehicle deceleration. The sensor signal is used in ABS control. If the sensor functions abnormally, the ABS warning light turns ON.DTC C1279/79 can be deleted when the deceleration sensor sends a deceleration sensor signal or the test mode ends. DTC C1279/79 is output only in the test mode.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| C1243/43 |
Following condition repeats 16 times: GL1 does not change when vehicle decelerates from 30 km/h (19 mph) to 0 km/h (0 mph) |
|
| C1244/44 |
When one of following (1 to 3) is detected: 1. Deceleration G calculated by ECU based on GL1 signal is not within -1.5 and 1.5 G for 1.2 sec. 2. When sensor operating voltage is not within 4.75 to 5.25 V 3. Deceleration sensor malfunction signal occurs more than 7 times |
|
| C1245/45 |
Difference between value calculated from deceleration sensor value and vehicle speed exceeds 0.35 G for at least 60 seconds |
|
| C1279/79 |
Detected only during test mode |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHOOSE DIAGNOSIS METHOD |
Choose the diagnosis method.
Method Method
Proceed to
Using intelligent tester
A
Not using intelligent tester
B
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (DECELERATION SENSOR 1) |
Check the Data List for proper functioning of the deceleration sensor.
Skid control ECU Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
Deceleration Sensor 1
Deceleration sensor 1
reading / min.: -1.869 G, max.: 1.869 G
Approx. 0 +/-0.13 G when vehicle is not moving.
Reading changes when vehicle is shaken
- OK:
- Deceleration value changes.
|
|
||||
| NG | |
| 3. INSPECT DECELERATION SENSOR |
![]() ![]() |
Remove the deceleration sensor.
Connect 3 dry cell batteries of 1.5 V in series.
- HINT:
- Do not apply 6 V or more to terminals 3 (VGS) and 2 (GGND).
Check the output voltage of terminal 1 (GL1) when the sensor is tilted forward and rearward.
- Standard voltage:
Tester Connection
Sensor Position
Specified Condition
1 (GL1) - Battery's negative (-) lead
Horizontal
Approx. 2.25 V
1 (GL1) - Battery's negative (-) lead
Tilted forward
Approx. 0.45 to 2.25 V
1 (GL1) - Battery's negative (-) lead
Tilted rearward
Approx. 2.25 to 4.05 V
- HINT:
- If the sensor is tilted too much, it may output the wrong value.
- If the voltage drops, the sensor should be replaced with a new one.
- When replacing the sensor, it should not be placed upside down.
- If the sensor is tilted too much, it may output the wrong value.
|
|
||||
| OK | |
| 4. CHECK WIRE HARNESS (SKID CONTROL ECU - DECELERATION SENSOR) |
![]() ![]() |
Disconnect the S2 ECU connector.
Disconnect the A17 sensor connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
S2-4 (GL1) - A17-1 (GL1)
Below 1 Ω
S2-7 (GGND) - A17-2 (GGND)
Below 1 Ω
S2-28 (VGS) - A17-3 (VGS)
Below 1 Ω
A17-1 (GL1) - Body ground
10 kΩ or higher
A17-2 (GGND) - Body ground
10 kΩ or higher
A17-3 (VGS) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK FOR DTC |
Install the deceleration sensor to the vehicle.
Clear the DTCs.
Drive the vehicle at 6 km/h (4 mph) or more.
Check for DTCs.
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | ||
| ||


