INSTALLATION
Removal / installation · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
| 1. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY |
Install the support with the 4 nuts.

- Torque:
- 14 N*m{ 145 kgf*cm , 10 ft.*lbf }
for 1KD-FTV and 2KD-FTV with Manual Transmission:

Attach the connector clamp and clamp to the brake pedal support sub-assembly.
Install the bolt to the support.

- Torque:
- 18 N*m{ 184 kgf*cm , 13 ft.*lbf }
| 2. CONNECT BRAKE MASTER CYLINDER PUSH ROD CLEVIS |
Apply a light coat of lithium soap base glycol grease to the clevis pin.

Connect the push rod clevis to the brake pedal.
Install the clevis pin and a new clip.
- NOTICE:
- The clip must be installed as shown in the illustration.
Install the return spring.
| 3. CHECK AND ADJUST BRAKE PEDAL HEIGHT |
![]() ![]() |
Check the pedal height.
- Pedal height from dash panel:
Model
Specified Condition
LHD (M/T)
152.9 to 162.9 mm (6.020 to 6.413 in.)
LHD (A/T)
154.1 to 164.1 mm (6.067 to 6.461 in.)
RHD (M/T)
156.9 to 166.9 mm (6.177 to 6.571 in.)
RHD (A/T)
158.1 to 168.1 mm (6.224 to 6.618 in.)
Adjust the pedal height.
Disconnect the connector from the stop light switch.
Remove the switch.
Loosen the push rod clevis lock nut.
Adjust the pedal height by turning the push rod.
Tighten the lock nut.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
Insert the switch into the adjuster until it slightly touches the pedal.

- NOTICE:
- Do not depress the pedal.
Turn the switch a quarter turn clockwise.

- Torque:
- 1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less
- NOTICE:
- Do not depress the pedal.
Connect the connector to the switch.
Check the switch clearance.
- Stop light switch clearance:
- 1.5 to 2.5 mm (0.0591 to 0.0984 in.)
| 4. CHECK BRAKE PEDAL FREE PLAY |
![]() ![]() |
Stop the engine. Depress the pedal several times until there is no vacuum in the booster. Then release the pedal.
Depress the pedal until resistance is felt.
Check the pedal's free play by measuring the distance between the position in the previous step and the pedal's released position.
- Pedal free play:
- 1.0 to 6.0 mm (0.0394 to 0.236 in.)
If the free play is as specified, proceed to the "check brake pedal reserve distance" procedure.
Check the switch clearance.
- Stop light switch clearance:
- 1.5 to 2.5 mm (0.0591 to 0.0984 in.)
If the clearance is as specified, troubleshoot the brake system and proceed to the "check brake pedal reserve distance" procedure.
| 5. CHECK BRAKE PEDAL RESERVE DISTANCE |
![]() ![]() |
Release the parking brake lever. Start the engine.
Depress the pedal and check the pedal reserve distance.
Depress the pedal with a force of 490 N (50 kgf, 110 lbf).
Measure the distance between the pedal and dash panel shown in the illustration.
- Pedal reserve distance:
Model
Specified Condition
LHD (2WD)
78.0 mm (3.071 in.)
LHD (4WD)
85.0 mm (3.347 in.)
RHD (2WD)
82.0 mm (3.228 in.)
RHD (4WD and pre-runner)
89.0 mm (3.504 in.)
| 6. INSTALL COMBINATION METER ASSEMBLY |
Install the combination meter (Click here).
| 7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



