2014 Hilux · Service Manual DRIVE LINE

REPLACEMENT

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. REMOVE NO. 1 ENGINE UNDER COVER

2. REMOVE NO. 2 ENGINE UNDER COVER

3. DRAIN DIFFERENTIAL OIL

  1. for front differential:

    1. Stop the vehicle on a level surface.

    2. A272242E01
      Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, remove the differential filler plug and gasket.
      SST
      09961-00950  
      Text in Illustration 
      *1
      10 mm Straight Hexagon Wrench
      *2
      10 mm Union Nut Wrench
      *3
      Socket Adaptor

    3. Remove the drain plug and gasket, and drain the oil.

    4. Install a new gasket and the drain plug.

      Torque:
      65 N*m{ 660 kgf*cm , 48 ft.*lbf }

  1. for rear differential:

    1. Stop the vehicle on a level surface.

    2. Remove the differential filler plug and gasket.

    3. Remove the drain plug and gasket, and drain the oil.

    4. Install a new gasket and the drain plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }


4. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
(Click here)

5. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


6. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

  1. C236642E01
    Using SST, tap out the oil seal.
    SST
    09308-00010  


7. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

  1. C236643E01
    Using SST and a hammer, tap in 2 new oil seals.
    SST
    09554-47010  
    09950-70010   (09951-07100)

    NOTICE:
    1. Make sure the LH and RH oil seals are installed to the proper locations.
    2. As a different side of SST is used for each oil seal, be sure to confirm that the correct side of SST is being used before tapping in an oil seal.
    3. Make sure that the lip of the oil seal is inserted into SST before tapping in the oil seal.
    4. As each side of SST is designed to tap in the corresponding oil seal to the proper depth, be sure to fully tap in the oil seal.
    5. Do not damage the oil seals.

    Standard Oil Seal Depth:
    Item
    Specified Condition
    for LH Side
    2.9 +/-0.45 mm (0.114 +/-0.0177 in.)
    for RH Side
    8.1 +/-0.45 mm (0.319 +/-0.0177 in.)

    Text in Illustration 
    *a
    for LH Side
    *b
    for RH Side
    *1
    Differential
    *2
    Seal

  1. Apply MP grease to the lip of each oil seal.


8. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
(Click here)

9. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


10. ADD DIFFERENTIAL OIL

  1. D025304E51
    Add differential oil so that the oil level is within 5 mm (0 to 0.196 in.) from the bottom lip of the differential filler plug hole.
    Text in Illustration 
    *a
    0 to 5 mm (0 to 0.196 in.)

    NOTICE:
    1. After changing the oil seal, drive the vehicle and then check the oil level again.
    2. Too much or too little oil will lead to differential problems.

    HINT:
    If necessary, fill the differential carrier assembly with hypoid gear oil.

    Recommended viscosity:
    Item
    Temperature
    Viscosity
    Front differential (w/ A.D.D.)
    SAE 75W-90
    Front differential (w/o A.D.D.)
    Rear differential
    Above -18°C (0°F)
    SAE 90
    Below -18°C (0°F)
    SAE 80W-90 or SAE 80W

    Differential oil type:
    Item
    Oil type
    Front differential
    Rear differential
    Hypoid gear oil API GL-5 or equivalent
    Rear differential (for LSD)
    Hypoid gear oil LSD API GL-5 or equivalent

    Standard front differential oil capacity:
    Item
    Capacity
    w/o A.D.D.
    1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.)
    w/ A.D.D.
    1.60 to 1.70 liters (1.69 to 1.79 US qts., 1.41 to 1.49 Imp. qts.)

    TMT made Standard rear differential oil capacity:
    Item
    Capacity
    2WD and w/ LSD
    3.15 to 3.25 liters (3.33 to 3.43 US qts., 2.78 to 2.86 Imp. qts.)
    4WD and w/o LSD
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)

    TSAM made :
    Item
    Capacity
    2WD and made for DANA
    2.30 to 2.40 liters (2.43 to 2.54 US qts., 2.02 to 2.11 Imp. qts.)
    4WD, Pre-runner and made for DANA
    (w/o LSD, A.D.D.)
    2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)
    w/ LSD for 2WD
    3.15 to 3.25 liters (3.33 to 3.43 US qts., 2.78 to 2.86 Imp. qts.)
    w/ LSD for 4WD
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)
    w/ Differential lock
    2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.60 Imp. qts.)

  1. Check for oil leakage when the oil level is low.

  1. for front differential:

    1. A272243E01
      Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, install a new gasket and the differential filler plug.
      SST
      09961-00950  
      Text in Illustration 
      *1
      10 mm Straight Hexagon Wrench
      *2
      10 mm Union Nut Wrench
      *3
      Socket Adaptor

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

      NOTICE:
      1. Make sure all the tools are connected in a straight line.
      2. Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

        Formula:
        T' = T x L3 / (L1 + L2 + L3)
        - T' = Spec. value of torque wrench
        - T = Value of specified tightening torque
        - L1 = Length of union nut wrench
        - L2 = Length of SST
        - L3 = Length of torque wrench

  1. for rear differential:

    1. Install a new gasket and the differential filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }


11. INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }


12. INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }

← COMPONENTS (from Aug 2013)REPLACEMENT (Aug 2012 – Jul 2013) →