2014 Hilux · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built from Jun 2011


1. INSTALL REAR LEAF SPRING ASSEMBLY LH
  1. Install the spring to the vehicle body.


2. INSTALL NO. 2 REAR LEAF SPRING SHACKLE SUB-ASSEMBLY
  1. Install the spring shackle to the spring and vehicle body.


3. TEMPORARILY INSTALL LEAF SPRING SHACKLE INNER PLATE
  1. Temporarily install the inner plate to the shackle No. 2 with the 2 washers and 2 nuts.

    HINT:
    After stabilizing the suspension, torque the nut.


4. TEMPORARILY INSTALL REAR LEAF SPRING BRACKET PIN OR PIN BOLT
  1. TMT Made Single cab:

    1. Temporarily install bracket pin with the washer and nut.

    2. Temporarily install the set bolt.

      HINT:
      1. The bracket pin can be installed from either side of the spring.
      2. After stabilizing the suspension, torque the nut.

  1. except TMT Made Single cab:
    Temporarily install the pin bolt with the washer and nut.

    HINT:
    After stabilizing the suspension, torque the nut.


5. TEMPORARILY INSTALL REAR SPRING U BOLT

F049968E01
  1. Temporarily install the 2 U bolts and U bolt seat with the 4 washers and 4 nuts.

    HINT:
    When tightening the U bolts, tighten the nuts in diagonal pairs.


6. INSTALL REAR SPRING BUMPER
  1. Install the spring bumper with the 2 bolts.


7. INSTALL REAR SHOCK ABSORBER ASSEMBLY

F050332E03
  1. Install the 2 washers to the axle housing.

  1. Install 4 new bushes to the absorber.

  1. Install the absorber (with the 4 bushes) to the U bolt seat and frame.

  1. Install the 2 washers.

  1. Temporarily tighten the 2 bolts.


8. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

C237683E02
Text in Illustration 
*1
No. 3 Parking Brake Cable
*2
No. 3 Clip
  1. Install the No. 3 parking brake cable with the 4 bolts and nut.

    Torque:
    for Bolt A, Nut C:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }
    for Bolt B:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Install the No. 3 clip.

  1. Connect the No. 3 parking brake cable to the parking brake shoe lever LH and backing plate LH.

    1. Connect the No. 3 parking brake cable to the backing plate with the 2 bolts.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    2. Connect the No. 3 parking brake cable to the parking brake shoe lever (Click here).


9. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Bounce the vehicle up and down several times to stabilize the suspension.


10. TIGHTEN LEAF SPRING SHACKLE INNER PLATE NUT
  1. Tighten the plate nut.

    Torque:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }


11. TIGHTEN REAR LEAF SPRING BRACKET PIN NUT
  1. Tighten the pin nut.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }


12. TIGHTEN REAR LEAF SPRING PIN SET BOLT
  1. Tighten the set bolt.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


13. TIGHTEN LEAF SPRING U BOLT SEAT NUT
  1. Tighten the 4 nuts.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }


14. INSTALL REAR WHEEL
  1. Install the wheel.

    Torque:
    for steel wheel:
    152 N*m{ 1550 kgf*cm , 112 ft.*lbf }
    for aluminum wheel:
    121 N*m{ 1234 kgf*cm , 89 ft.*lbf }

← REASSEMBLY (from Jun 2011)COMPONENTS (from Jun 2011) →