2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jun 2011


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A114241
    Remove the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug and then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


    A114242E01


3. REMOVE RADIATOR HOSE INLET

4. REMOVE VANE PUMP V BELT

  1. A121092E01
    Loosen the bolt A and nut B, and remove the V belt.


5. REMOVE COOLER COMPRESSOR V BELT (w/ Air Conditioning System)

  1. A121093E01
    Loosen the nut A and bolt B, and remove the V belt.


6. REMOVE FAN AND GENERATOR V BELT (w/o Air Conditioning System)

  1. A115631E01
    Loosen the bolts A and B, and remove the V belt.


7. REMOVE FAN AND GENERATOR V BELT (w/ Air Conditioning System)

  1. A115632E01
    Loosen the bolts A and B.

  1. Loosen the adjusting bolt C, and remove the V belt.


8. REMOVE FAN SHROUD

  1. A114244
    Remove the 3 bolts and oil reservoir.

  1. Disconnect the No. 1 and No. 2 water by-pass hoses from the tank upper and lower.

  1. Remove the bolt and radiator reservoir.

  1. Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the vane pump V belt, cooler compressor V belt and fan and generator V belt (Click here).

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.


9. REMOVE FAN PULLEY

10. DISCONNECT COOLER COMPRESSOR (w/ Air Conditioning System)

  1. A123646
    Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.


11. REMOVE COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

  1. A112016E01
    Remove the bolt and spacer.

  1. A121135E01
    Remove the 4 bolts and compressor mounting bracket.


12. REMOVE VANE PUMP DRIVE PULLEY

A112013
  1. w/o Air conditioning:
    Remove the 4 bolts, vane pump drive pulley and vane pump drive pulley spacer.

  1. w/ Air conditioning:
    Remove the 4 bolts and vane pump drive and No. 2 crankshaft pulleys.


13. REMOVE CRANKSHAFT PULLEY

A058720E01
  1. Using SST, remove the pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A058719E01
    Using SST, remove the pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)
    09950-60010   (09951-00490)
    09950-40011   (09957-04010)


14. REMOVE TIMING BELT COVER

  1. A112017
    Remove the 11 bolts, washers, timing belt cover and 2 gaskets.


15. REMOVE TIMING BELT GUIDE
  1. Remove the timing belt guide.


16. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A112064
    Turn the crankshaft pulley and align its groove with the timing pointer.

  1. Check that the valve lifters on the No. 1 cylinder are loose and valve lifters on the No. 4 are tight.
    If not, turn the crankshaft one revolution (360°) and align the mark as above.


17. REMOVE TIMING BELT

  1. A058721E01
    Remove the timing belt.

    HINT:
    If reusing the timing belt, draw a direction arrow on the timing belt (in the direction of engine revolution), and place matchmarks on the pulleys and timing belt.

  1. A058730E02
    Turn the crankshaft 90° counterclockwise, and put the timing mark of the crankshaft timing pulley with the protrusion of the timing gear case.

    NOTICE:
    If the timing belt is disengaged, having the crankshaft timing pulley at the wrong angle can cause the piston head and valve head to come into contact with each other when you remove the camshaft timing pulley, causing damage. So always set the crankshaft pulley at the correct angle.

  1. A058731E01
    Loosen the No. 1 timing belt idler bolt (A), and shift the idler to the left as far as possible.

  1. Temporarily tighten the pulley bolt (A), and then relieve the timing belt tension.

  1. Remove the timing belt.


18. REMOVE AIR CLEANER HOSE
  1. Disconnect the IAT sensor connector.

  1. Detach the clamp of the IAT sensor harness.

  1. Loosen the 2 clamps from the air cleaner hose.

  1. Remove the air cleaner hose.


19. REMOVE INTAKE PIPE ASSEMBLY

  1. A114290
    Remove the 2 bolts and loosen the hose clamp.


20. REMOVE VENTURI

  1. A111052E02
    Disconnect the throttle open switch connector.

  1. A111053E02
    Disconnect the throttle control motor connector.

  1. Remove the venturi and gasket.


21. REMOVE INJECTION PIPE SET

  1. A121940
    Using a union nut wrench, loosen the 8 union nuts of the 4 injection pipes.

  1. Remove the 2 nuts, 2 upper pipe clamps and 4 injection pipes with lower pipe clamps.


22. REMOVE INJECTION PUMP DRIVE PULLEY

  1. A071313E01
    Using SST, remove the pulley nut.
    SST
    09213-14010   (91651-60865)
    09330-00021  

  1. A071314E01
    Using SST, remove the drive pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)


23. REMOVE INJECTION PUMP ASSEMBLY

  1. A121086E01
    Disconnect the engine speed sensor connector.

  1. Disconnect the spill control valve connector.

  1. Disconnect the correction unit connector.

  1. Disconnect the timing control valve connector.

  1. Disconnect the fuel temperature sensor connector.

  1. Disconnect the engine wire clamp.

  1. Disconnect the 3 fuel hoses.

  1. A071318E01
    Remove the 3 bolts and injection pump stay.

  1. Remove the 2 nuts and injection pump.

← ON-VEHICLE INSPECTION (from Jun 2011)DISASSEMBLY (from Jun 2011) →