2014 Hilux · Service Manual BODY

Remote Up / Down Function does not Operate

Circuit diagnosis · Vehicles built from Jun 2011

DESCRIPTION

With the ignition switch ON, the power window regulator master switch assembly transmits remote switch signals to the power window regulator switches of the front passenger side power window and rear power windows. Then, each power window regulator switch drives its respective power window regulator motor*1 or door window regulator*2.
  1. *1: w/o Regulator
  2. *2: w/ Regulator

WIRING DIAGRAM

B276856E05
B289718E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
  1. Turn the window lock switch off and operate the switches on the power window regulator master switch assembly. Check that the remote up/down function operates normally.

    OK:
    Remote up/down function operates normally.



NG
Go to step 2
OK

END

2. CHECK MANUAL UP/DOWN FUNCTION
  1. Check that the front passenger side power window and rear power window manual up/down function operates normally.

    OK:
    Manual up/down function operates normally.



NG
GO TO PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - FRONT POWER WINDOW REGULATOR SWITCH [FOR FRONT PASSENGER SIDE])
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the P4 power window regulator master switch assembly connector.

  1. Disconnect the P9 front power window regulator switch assembly (for front passenger side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Double Cab, w/o Jam Protection 
    Tester Connection
    Condition
    Specified Condition
    P4-18 (U) - P9-1*1
    P4-10 (U) - P9-1*2
    Always
    Below 1 Ω
    P4-15 (D) - P9-4*1
    P4-13 (D) - P9-4*2
    Always
    Below 1 Ω
    P4-18 (U) or P9-1 - Body ground*1
    P4-10 (U) or P9-1 - Body ground*2
    Always
    10 kΩ or higher
    P4-15 (D) or P9-4 - Body ground*1
    P4-13 (D) or P9-4 - Body ground*2
    Always
    10 kΩ or higher
    except Double Cab, w/o Jam Protection 
    Tester Connection
    Condition
    Specified Condition
    P4-8 (U) - P9-1
    Always
    Below 1 Ω
    P4-10 (D) - P9-4*1
    P4-1 (D) - P9-4*2
    Always
    Below 1 Ω
    P4-8 (U) or P9-1 - Body ground
    Always
    10 kΩ or higher
    P4-10 (D) or P9-4 - Body ground*1
    P4-1 (D) or P9-4 - Body ground*2
    Always
    10 kΩ or higher
    w/ Jam Protection 
    Tester Connection
    Condition
    Specified Condition
    P4-13 (U) - P9-1
    Always
    Below 1 Ω
    P4-15 (D) - P9-4
    Always
    Below 1 Ω
    P4-13 (U) or P9-1 - Body ground
    Always
    10 kΩ or higher
    P4-15 (D) or P9-4 - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for Double Cab)
    A
    OK (except Double Cab)
    B
    NG
    C



B
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - REAR POWER WINDOW REGULATOR SWITCH LH)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the P4 power window regulator master switch assembly connector.

  1. Disconnect the P10 rear power window regulator switch assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Jam Protection 
    Tester Connection
    Condition
    Specified Condition
    P4-12 (U) - P10-1*1
    P4-18 (U) - P10-1*2
    Always
    Below 1 Ω
    P4-13 (D) - P10-4*1
    P4-12 (D) - P10-4*1
    Always
    Below 1 Ω
    P4-12 (U) or P10-1 - Body ground*1
    P4-18 (U) or P10-1 - Body ground*2
    Always
    10 kΩ or higher
    P4-13 (D) or P10-4 - Body ground*1
    P4-12 (D) or P10-4 - Body ground*1
    Always
    10 kΩ or higher
    w/ Jam Protection 
    Tester Connection
    Condition
    Specified Condition
    P4-12 (U) - P10-1
    Always
    Below 1 Ω
    P4-10 (D) - P10-4
    Always
    Below 1 Ω
    P4-12 (U) or P10-1 - Body ground
    Always
    10 kΩ or higher
    P4-10 (D) or P10-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - REAR POWER WINDOW REGULATOR SWITCH RH)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the P4 power window regulator master switch assembly connector.

  1. Disconnect the P11 rear power window regulator switch assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Jam Protection 
    Tester Connection
    Condition
    Specified Condition
    P4-10 (U) - P11-1*1
    P4-16 (U) - P11-1*2
    Always
    Below 1 Ω
    P4-16 (D) - P11-4*1
    P4-15 (D) - P11-4*2
    Always
    Below 1 Ω
    P4-10 (U) or P11-1 - Body ground*1
    P4-16 (U) or P11-1 - Body ground*2
    Always
    10 kΩ or higher
    P4-16 (D) or P11-4 - Body ground*1
    P4-15 (D) or P11-4 - Body ground*2
    Always
    10 kΩ or higher
    w/ Jam Protection 
    Tester Connection
    Condition
    Specified Condition
    P4-18 (U) - P11-1
    Always
    Below 1 Ω
    P4-16 (D) - P11-4
    Always
    Below 1 Ω
    P4-18 (U) or P11-1 - Body ground
    Always
    10 kΩ or higher
    P4-16 (D) or P11-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


← Auto Up / Down Function does not Operate (from Aug 2013)Driver Side Power Window Manual Function does not Operate with Power Window Master Switch (from Jun 2011) →