2014 Hilux · Service Manual BODY

Driver Side Power Window Manual Function does not Operate with Power Window Master Switch

Circuit diagnosis · Vehicles built from Jun 2011

DESCRIPTION

If the manual up/down function does not operate, a malfunction may be present in the power window regulator master switch assembly, front power window regulator motor assembly (for driver side)*1, front door window regulator sub-assembly (for driver side)*2 or wire harness.
  1. *1: w/o Regulator
  2. *2: w/ Regulator

WIRING DIAGRAM

B289858E01
B289859E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

  1. except Double Cab, w/o Jam Protection:

    1. B290653E01
      Disconnect the P4 power window regulator master switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      P4-9 (B) - Body ground
      Ignition switch ON
      11 to 14 V
      P4-9 (B) - Body ground
      Ignition switch off
      Below 1 V
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      P4-9 (B) - Body ground
      Ignition switch ON
      11 to 14 V
      P4-9 (B) - Body ground
      Ignition switch off
      Below 1 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      P4-1 (E) - Body ground
      Always
      Below 1 Ω
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      P4-10 (E) - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Front view of wire harness connector
      (to Power Window Regulator Master Switch Assembly)

  1. for Double Cab, w/o Jam Protection:

    1. B276330E18
      Disconnect the P4 power window regulator master switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      P4-6 (B) - Body ground
      Ignition switch ON
      11 to 14 V
      P4-6 (B) - Body ground
      Ignition switch off
      Below 1 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P4-3 (E) - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Power Window Regulator Master Switch Assembly)

  1. w/ Jam Protection:

    1. B276330E14
      Disconnect the P4 power window regulator master switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      P4-7 (BW) - Body ground
      Always
      11 to 14 V
      P4-6 (B) - Body ground
      Ignition switch ON
      11 to 14 V
      P4-6 (B) - Body ground
      Ignition switch off
      Below 1 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P4-1 (E) - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Power Window Regulator Master Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER SIDE) OR FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (FOR DRIVER SIDE)

  1. except Double Cab, w/o Jam Protection:

    1. B290653E02
      Disconnect the P4 power window regulator master switch assembly connector.

    2. Using a service wire, connect the terminals according to the table below.

    3. Check operation of the front power window regulator motor assembly (for driver side)*1 or front door window regulator sub-assembly (for driver side)*2.

      1. *1: w/ Regulator
      2. *2: w/o Regulator

      OK:
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      P4-3 (U) - P4-9 (B)
      P4-4 (D) - Body ground
      Always
      Power window moves up
      P4-3 (U) - Body ground
      P4-9 (B) - P4-4 (D)
      Always
      Power window moves down
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      P4-2 (U) - P4-9 (B)
      P4-5 (D) - Body ground
      Always
      Power window moves up
      P4-2 (U) - Body ground
      P4-9 (B) - P4-5 (D)
      Always
      Power window moves down

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Front view of wire harness connector
      (to Power Window Regulator Master Switch Assembly)

  1. for Double Cab, w/o Jam Protection:

    1. B276330E19
      Disconnect the P4 power window regulator master switch assembly connector.

    2. Using a service wire, connect the terminals according to the table below.

    3. Check operation of the front power window regulator motor assembly (for driver side)*1 or front door window regulator sub-assembly (for driver side)*2.

      1. *1: w/ Regulator
      2. *2: w/o Regulator

      OK:
      Tester Connection
      Condition
      Specified Condition
      P4-4 (U) - P4-6 (B)
      P4-9 (D) - Body ground
      Always
      Power window moves up
      P4-4 (U) - Body ground
      P4-6 (B) - P4-9 (D)
      Always
      Power window moves down

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Power Window Regulator Master Switch Assembly)

  1. w/ Jam Protection:

    1. B276330E17
      Disconnect the P4 power window regulator master switch assembly connector.

    2. Using a service wire, connect the terminals according to the table below.

    3. Check operation of the front power window regulator motor assembly (for driver side)*1 or front door window regulator sub-assembly (for driver side)*2.

      1. *1: w/ Regulator
      2. *2: w/o Regulator

      OK:
      Tester Connection
      Condition
      Specified Condition
      P4-4 (U) - P4-7 (BW)
      P4-9 (D) - Body ground
      Always
      Power window moves up
      P4-4 (U) - Body ground
      P4-7 (BW) - P4-9 (D)
      Always
      Power window moves down

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Power Window Regulator Master Switch Assembly)



NG
Go to step 3
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

3. CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

  1. except Double Cab, w/o Jam Protection:

    1. B290666E01
      Remove the power window regulator master switch assembly with its connectors still connected.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      3 (U) - 1(E)
      Ignition switch ON, driver side power window switch off → up (manual operation)
      Below 1 V → 11 to 14 V
      3 (U) - 1(E)
      Ignition switch ON, driver side power window fully open → driver side power window switch up (auto operation) → driver side power window fully closed
      Below 1 V → 11 to 14 V → Below 1 V
      5 (D) - 10 (E)
      Ignition switch ON, driver side power window switch off → down (manual operation)
      Below 1 V → 11 to 14 V
      4 (D) - 1 (E)
      Ignition switch ON, driver side power window fully closed → driver side power window switch down (auto operation) → driver side power window fully open
      Below 1 V → 11 to 14 V → Below 1 V
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      2 (U) - 10 (E)
      Ignition switch ON, driver side power window switch off → up (manual operation)
      Below 1 V → 11 to 14 V
      2 (U) - 10 (E)
      Ignition switch ON, driver side power window fully open → driver side power window switch up (auto operation) → driver side power window fully closed
      Below 1 V → 11 to 14 V → Below 1 V
      5 (D) - 10 (E)
      Ignition switch ON, driver side power window switch off → down (manual operation)
      Below 1 V → 11 to 14 V
      5 (D) - 10 (E)
      Ignition switch ON, driver side power window fully closed → driver side power window switch down (auto operation) → driver side power window fully open
      Below 1 V → 11 to 14 V → Below 1 V

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Component with harness connected
      (Power Window Regulator Master Switch Assembly)

  1. for Double Cab, w/o Jam Protection:

    1. B276285E17
      Remove the power window regulator master switch assembly with its connectors still connected.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      4 (U) - 3 (E)
      Ignition switch ON, driver side power window switch off → up (manual operation)
      Below 1 V → 11 to 14 V
      4 (U) - 3 (E)
      Ignition switch ON, driver side power window fully open → driver side power window switch up (auto operation) → driver side power window fully closed
      Below 1 V → 11 to 14 V → Below 1 V
      9 (D) - 3 (E)
      Ignition switch ON, driver side power window switch off → down (manual operation)
      Below 1 V → 11 to 14 V
      9 (D) - 3 (E)
      Ignition switch ON, driver side power window fully closed → driver side power window switch down (auto operation) → driver side power window fully open
      Below 1 V → 11 to 14 V → Below 1 V

      Text in Illustration 
      *a
      Component with harness connected
      (Power Window Regulator Master Switch Assembly)

  1. w/ Jam Protection:

    1. B276285E05
      Remove the power window regulator master switch assembly with its connectors still connected.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      4 (U) - 1 (E)
      Ignition switch ON, driver side power window switch off → up (manual operation)
      Below 1 V → 11 to 14 V
      4 (U) - 1 (E)
      Ignition switch ON, driver side power window fully open → driver side power window switch up (auto operation) → driver side power window fully closed
      Below 1 V → 11 to 14 V → Below 1 V
      9 (D) - 1 (E)
      Ignition switch ON, driver side power window switch off → down (manual operation)
      Below 1 V → 11 to 14 V
      9 (D) - 1 (E)
      Ignition switch ON, driver side power window fully closed → driver side power window switch down (auto operation) → driver side power window fully open
      Below 1 V → 11 to 14 V → Below 1 V

      Text in Illustration 
      *a
      Component with harness connected
      (Power Window Regulator Master Switch Assembly)



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR [FOR DRIVER SIDE] OR FRONT DOOR WINDOW REGULATOR [FOR DRIVER SIDE])
  1. *1: for LHD
  2. *2: for RHD
  1. except Double Cab, w/o Jam Protection:

    1. Disconnect the P4 power window regulator master switch assembly connector.

    2. w/o Regulator:

      1. Disconnect the P5*1 or P6*2 front power window regulator motor assembly (for driver side) connector.

    3. w/ Regulator:

      1. Disconnect the P5*1 or P6*2 front door window regulator sub-assembly (for driver side) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      P4-4 (D) - P5-1 (D)
      Always
      Below 1 Ω
      P4-3 (U) - P5-2 (U)
      Always
      Below 1 Ω
      P4-4 (D) or P5-1 (D) - Body ground
      Always
      10 kΩ or higher
      P4-3 (U) or P5-2 (U) - Body ground
      Always
      10 kΩ or higher
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      P4-5 (D) - P6-1 (D)
      Always
      Below 1 Ω
      P4-2 (U) - P6-2 (U)
      Always
      Below 1 Ω
      P4-5 (D) or P6-1 (D) - Body ground
      Always
      10 kΩ or higher
      P4-2 (U) or P6-2 (U) - Body ground
      Always
      10 kΩ or higher

  1. for Double Cab, w/o Jam Protection:

    1. Disconnect the P4 power window regulator master switch assembly connector.

    2. w/o Regulator:

      1. Disconnect the P5*1 or P6*2 front power window regulator motor assembly (for driver side) connector.

    3. w/ Regulator:

      1. Disconnect the P5*1 or P6*2 front door window regulator sub-assembly (for driver side) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      P4-9 (D) - P5-1 (D)
      Always
      Below 1 Ω
      P4-4 (U) - P5-2 (U)
      Always
      Below 1 Ω
      P4-9 (D) or P5-1 (D) - Body ground
      Always
      10 kΩ or higher
      P4-4 (U) or P5-2 (U) - Body ground
      Always
      10 kΩ or higher
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      P4-9 (D) - P6-1 (D)
      Always
      Below 1 Ω
      P4-4 (U) - P6-2 (U)
      Always
      Below 1 Ω
      P4-9 (D) or P6-1 (D) - Body ground
      Always
      10 kΩ or higher
      P4-4 (U) or P6-2 (U) - Body ground
      Always
      10 kΩ or higher

  1. w/ Jam Protection:

    1. Disconnect the P4 power window regulator master switch assembly connector.

    2. w/o Regulator:

      1. Disconnect the P5*1 or P6*2 front power window regulator motor assembly (for driver side) connector.

    3. w/ Regulator:

      1. Disconnect the P5*1 or P6*2 front door window regulator sub-assembly (for driver side) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      P4-9 (D) - P5-1 (D)
      Always
      Below 1 Ω
      P4-4 (U) - P5-2 (U)
      Always
      Below 1 Ω
      P4-9 (D) or P5-1 (D) - Body ground
      Always
      10 kΩ or higher
      P4-4 (U) or P5-2 (U) - Body ground
      Always
      10 kΩ or higher
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      P4-9 (D) - P6-1 (D)
      Always
      Below 1 Ω
      P4-4 (U) - P6-2 (U)
      Always
      Below 1 Ω
      P4-9 (D) or P6-1 (D) - Body ground
      Always
      10 kΩ or higher
      P4-4 (U) or P6-2 (U) - Body ground
      Always
      10 kΩ or higher

Result 
Result
Proceed to
NG
A
OK (w/o Regulator)
B
OK (w/ Regulator)
C


B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER SIDE)

C
REPLACE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (FOR DRIVER SIDE)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR


← Remote Up / Down Function does not Operate (from Jun 2011)Front Passenger Side Power Window Manual Function does not Operate with Front Passenger Side Power Window Switch (from Jun 2011) →