2014 Hilux · Service Manual BODY

Front Passenger Side Power Window Manual Function does not Operate with Front Passenger Side Power Window Switch

Circuit diagnosis · Vehicles built from Jun 2011

DESCRIPTION

If the front passenger side manual up/down function does not operate, a malfunction may be present in the front power window regulator motor assembly (for front passenger side)*1 or front door window regulator sub-assembly (for front passenger side)*2, front power window regulator switch assembly (for front passenger side), power window regulator master switch assembly or wire harness.
  1. *1: w/o Regulator
  2. *2: w/ Regulator

WIRING DIAGRAM

B290668E01
B290673E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY [FOR FRONT PASSENGER SIDE] - BATTERY)

  1. B276367E05
    Disconnect the P9 front power window regulator switch assembly (for front passenger side) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P9-3 - Body ground
    Ignition switch ON
    11 to 14 V
    P9-3 - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Power Window Regulator Switch Assembly [for Front Passenger Side])



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR FRONT PASSENGER SIDE)

  1. B280844
    Remove the front power window regulator switch assembly (for front passenger side).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 - 4
    2 - 3
    UP
    Below 1 Ω
    5 - 4
    2 - 1
    OFF
    Below 1 Ω
    5 - 3
    2 - 1
    DOWN
    Below 1 Ω



NG
REPLACE FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR FRONT PASSENGER SIDE)
OK


3. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH [FOR FRONT PASSENGER SIDE] - FRONT POWER WINDOW REGULATOR MOTOR [FOR FRONT PASSENGER SIDE]) OR FRONT DOOR WINDOW REGULATOR [FOR FRONT PASSENGER SIDE])
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the P4 front power window regulator switch assembly (for front passenger side) connector.

  1. w/o Regulator:

    1. Disconnect the P5*1 or P6*2 front power window regulator motor assembly (for front passenger side) connector.

  1. w/ Regulator:

    1. Disconnect the P5*1 or P6*2 front door window regulator sub-assembly (for front passenger side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    P9-5 - P6-1
    Always
    Below 1 Ω
    P9-2 - P6-2
    Always
    Below 1 Ω
    P9-5 or P6-1 - Body ground
    Always
    10 kΩ or higher
    P9-2 or P6-2 - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    P9-5 - P5-1
    Always
    Below 1 Ω
    P9-2 - P5-2
    Always
    Below 1 Ω
    P9-5 or P5-1 - Body ground
    Always
    10 kΩ or higher
    P9-2 or P5-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER SIDE) OR FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (FOR FRONT PASSENGER SIDE)

  1. w/o Regulator:

    1. B284223E02
      Remove the front power window regulator motor assembly (for front passenger side).

    2. Apply battery voltage to connector terminals 1 and 2.

    3. Check that the motor gear rotates smoothly as follows.

      OK:
      for LHD 
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2
      Battery negative (-) → 1
      Motor gear rotates clockwise
      Battery positive (+) → 1
      Battery negative (-) → 2
      Motor gear rotates counterclockwise
      for RHD 
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2
      Battery negative (-) → 1
      Motor gear rotates counterclockwise
      Battery positive (+) → 1
      Battery negative (-) → 2
      Motor gear rotates clockwise

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *1
      Motor Gear
      V100135
      Clockwise
      V100136
      Counterclockwise

  1. w/ Regulator:B290675E01

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    V100135
    Up
    V100136
    Down
    1. Remove the front door window regulator sub-assembly (for front passenger side).

    2. Apply battery voltage to connector terminals 1 and 2.

    3. Check that the arm of window regulator rotates smoothly as follows.

      OK:
      for LHD 
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2
      Battery negative (-) → 1
      Arm of window regulator rotates clockwise (Up)
      Battery positive (+) → 1
      Battery negative (-) → 2
      Arm of window regulator rotates counterclockwise (Down)
      for RHD 
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2
      Battery negative (-) → 1
      Arm of window regulator rotates counterclockwise (Up)
      Battery positive (+) → 1
      Battery negative (-) → 2
      Arm of window regulator rotates clockwise (Down)

Result 
Result
Proceed to
OK
A
NG (w/o Regulator)
B
NG (w/ Regulator)
C


B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER SIDE)

C
REPLACE FRONT DOOR REGULATOR SUB-ASSEMBLY (FOR FRONT PASSENGER SIDE)
A


5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY [FOR FRONT PASSENGER SIDE])
  1. except Double Cab, w/o Jam Protection:

    1. Disconnect the P4 power window regulator master switch assembly connector.

    2. Disconnect the P9 front power window regulator switch assembly (for front passenger side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      P4-8 (U) - P9-1
      Always
      Below 1 Ω
      P4-10 (D) - P9-4
      Always
      Below 1 Ω
      P4-8 (U) or P9-1 - Body ground
      Always
      10 kΩ or higher
      P4-10 (D) or P9-4 - Body ground
      Always
      10 kΩ or higher
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      P4-8 (U) - P9-1
      Always
      Below 1 Ω
      P4-1 (D) - P9-4
      Always
      Below 1 Ω
      P4-8 (U) or P9-1 - Body ground
      Always
      10 kΩ or higher
      P4-1 (D) or P9-4 - Body ground
      Always
      10 kΩ or higher

  1. for Double Cab, w/o Jam Protection:

    1. Disconnect the P4 power window regulator master switch assembly connector.

    2. Disconnect the P9 front power window regulator switch assembly (for front passenger side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      P4-18 (U) - P9-1
      Always
      Below 1 Ω
      P4-15 (D) - P9-4
      Always
      Below 1 Ω
      P4-18 (U) or P9-1 - Body ground
      Always
      10 kΩ or higher
      P4-15 (D) or P9-4 - Body ground
      Always
      10 kΩ or higher
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      P4-10 (U) - P9-1
      Always
      Below 1 Ω
      P4-13 (D) - P9-4
      Always
      Below 1 Ω
      P4-10 (U) or P9-1 - Body ground
      Always
      10 kΩ or higher
      P4-13 (D) or P9-4 - Body ground
      Always
      10 kΩ or higher

  1. w/ Jam Protection:

    1. Disconnect the P4 power window regulator master switch assembly connector.

    2. Disconnect the P9 front power window regulator switch assembly (for front passenger side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P4-13 (U) - P9-1
      Always
      Below 1 Ω
      P4-15 (D) - P9-4
      Always
      Below 1 Ω
      P4-13 (U) or P9-1 - Body ground
      Always
      10 kΩ or higher
      P4-15 (D) or P9-4 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


← Driver Side Power Window Manual Function does not Operate with Power Window Master Switch (from Jun 2011)Rear Power Window LH Manual Function does not Operate with Rear Power Window Switch LH (from Jun 2011) →