2014 Hilux · Service Manual BODY

Power Windows do not Operate at All

Circuit diagnosis · Vehicles built from Jun 2011

DESCRIPTION

If all of the power windows do not operate, the power window regulator master switch assembly may have no power or may be malfunctioning.

WIRING DIAGRAM

B278482E04

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

  1. except Double Cab, w/o Jam Protection:

    1. B290653E01
      Disconnect the P4 power window regulator master switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LHD 
      Tester Connection
      Switch Condition
      Specified Condition
      P4-9 (B) - Body ground
      Ignition switch ON
      11 to 14 V
      P4-9 (B) - Body ground
      Ignition switch off
      Below 1 V
      for RHD 
      Tester Connection
      Switch Condition
      Specified Condition
      P4-9 (B) - Body ground
      Ignition switch ON
      11 to 14 V
      P4-9 (B) - Body ground
      Ignition switch off
      Below 1 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      P4-1 (E) - Body ground
      Always
      Below 1 Ω
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      P4-10 (E) - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Front view of wire harness connector
      (to Power Window Regulator Master Switch Assembly)

  1. for Double Cab, w/o Jam Protection:

    1. B276330E18
      Disconnect the P4 power window regulator master switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      P4-6 (B) - Body ground
      Ignition switch ON
      11 to 14 V
      P4-6 (B) - Body ground
      Ignition switch off
      Below 1 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P4-3 (E) - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Power Window Regulator Master Switch Assembly)

  1. w/ Jam Protection:

    1. B276330E14
      Disconnect the P4 power window regulator master switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      P4-7 (BW) - Body ground
      Always
      11 to 14 V
      P4-6 (B) - Body ground
      Ignition switch ON
      11 to 14 V
      P4-6 (B) - Body ground
      Ignition switch off
      Below 1 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P4-1 (E) - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Power Window Regulator Master Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


← Rear Power Window RH Manual Function does not Operate with Rear Power Window Switch RH (from Jun 2011)Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated) (from Jun 2011) →